manualshive.com logo in svg

Sonex Aircraft Aerovee 2.1, Сборка и инструкция по установке

Поделиться
Скачать
Sonex Aircraft Aerovee 2.1 Скачать руководство пользователя страница 39

39

AeroVee 2.1 

Rev Z. 01/14/2015

Sonex Aircraft

 LLC

 

 © 2014 All Rights Reserved

MOUNTING the ENGINE

Parts Required

__ Motor Mount Shock Bushings (Qty. 8), ACV-P01-19
__ 3/8" ID x 1.25" OD Fender Washer (Qty. 16), ACV-Z01-40
__ AN4-36A Bolt (Qty. 4, not supplied)
__ AN363-428 Nut (Qty. 4, not supplied)
__ AN960-416 Washer (as needed, not supplied)

A typical engine mount and shock-rubber installation. A mini-

mum of two ACV-Z01-40 washers (1/8" thick total, minimum) 

must be placed against the front bushing. Additional washers 

may be used as needed, and washers may be used behind the 

rear bushings as spacers to shim the thrust line as needed.

Sonex Aircraft Airframes

Bolting the engine to the engine mount is shown in detail in 

the "Engine Installation, AeroVee" drawing of your airframe 

plans and on the next page of this manual, however, these few 

notes may save you some time.

All Airframes

mount Bushings

 

The engine mount bushings will go on the engine mount much 

easier if they lightly lubricated with soapy water.

Lifting the engine

 

When lifting the engine into place care must be taken to make 

sure the pushrod tubes are not damaged.

installing the mount Bolts

 

The head of the mounting bolts may be inserted in either 

direction.

Содержание Aerovee 2.1







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды