background image

Model 464 Electronic Pump Control Unit User Guide

Page 3

2.0  Control Unit Operation

2.1  Start Up

Press any button on the keypad to turn the Control Unit on.  When first starting 

the Control Unit with new batteries, or restarting after replacing the batteries, 

the Control Unit will perform a self-test to identify any faults that may exist.  

The start-up screen is shown first (Figure 2-1 Start-up Screen After Replacing 

Batteries); following a short pause the main menu will be displayed.  

Figure 2-1 Start-up Screen After Replacing Batteries

ECU 464 V2.000

Copyright (c) 2016

Solinst Canada Ltd.

+1 (905) 873-2255

2.1.1  Main Menu

There are four main menu items for the Electronic Control Unit (Figure 2-2).  

Preset Flow Rates: allows you to select a flow rate with predefined drive and vent 

cycles (Low Flow, Medium Flow, or High Flow).

User Flow Rates: allows you to create user-defined flow rates, save flow rates, 

select and edit saved flow rates. 

LCD Contrast: enables you to adjust the brightness of the display.

About: will display information about the Control Unit, including firmware 

version and Solinst contact information. 

Figure 2-2 Model 464 Main Menu

User Flow Rates
LCD Contrast
About

ECU 464-125 Main

Preset Flow Rates

4:59 Min

99%

  NOTE

The Control Unit does not come 
with the batteries installed.

 

  NOTE

Turning the Control Unit on, 
displays the last screen shown at 
the time of shut-down.

Содержание 464 Mk3





















Отзывы: