Solid State Logic AWS 924 страница 101 Скачать руководство пользователя | Manualshive

Страница: 101 / 242

background image

Automation

Glide frames:

Sets the ramp time in frames for the automation SNAP mode. (range 0 - 255)

Rollback threshold frames:

Sets the number of consecutive frames that the system needs to see to

determine if a Rollback has taken place. The range is 2 - 10; the default is 2.

Increase as required if a Rollback occurs when you stop the timecode master.

In Mix show:

When using the automation, you have a choice of what is displayed on the

console’s channel scribble strips (and below the Group and Master fader

levels in the Centre Section TFT screen). The choices are:
Automation Mode: displays the status of the faders – Auto, Safe or Manual;
Channel names in Mix running: displays the channel names once

Execute

is

pressed in automation,
Channel names: displays the channels names regardless.

Latched Match and Play

(ON/OFF) Normally Match and Play are automatically deselected after a Cut

switch is operated. This option latches the Match or Play function until

deselected manually.

Talkback

Talkback switches are:

Select the operation of the talkback buttons: Momentary / Latching / Auto

(Play) / Auto (Record).

Listen switch is:

Select the operation of the Listen buttons: Latching / Auto (Play) / Auto

(Record).

Red light switch is:

Select the operation of the Red Light: Manual / Auto (Play) / Auto (Record).

TB switches disable Listen:

This allows the Listen function to be switched off when talkback is activated,

thus avoiding feedback problems.

TB to FB:

(Sums / Replaces) When assigning talkback to foldbacks, this option defines

whether talkback sums with or replaces the normal foldback signal.

See

Communications

for more details of these options

Monitor section

Monitor Gain Display:

The calibration of the main monitor Gain pot and display can be set to one

of three industry-standard monitoring modes: Music (Off to 11) / Film (Off

to 95dB) / Gain (Off to 0dB)

Monitor Set CAL level:

When in Film mode, adjust the calibrated listening level: 70 - 90 (dB).

See

Monitor Level Display and Calibrated listening level

for more details of these options

Solo Gain boost:

Automatically increases the monitor level when a SOLO or AFL is activated

(Range: 0-10dB).

Isolated channels AFL on solo:

Set solo-isolated channels to automatically solo in AFL (ON/OFF).

Desk Setup

Input Cut Enable:

If set ON, the channel strip

CUT

button will cut prefade sends, ie. Aux and

CHOP sends (ON / OFF).

Analogue Meter Scaling:

Set the analogue level corresponding to 0dBfs on the console meters. (Range

18, 20, 22, 24 dBu).

Analogue Operations

AWS 924-948 Owner’s Manual

Page 3-29

«
...
99
100
101
102
103
...
»

Содержание AWS 924



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWS 924

Бренд: BakeMark Страницы: 5

Бренд: Yamaha Страницы: 401

Бренд: Yamaha Страницы: 65

Бренд: D&R Страницы: 17

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 19

Бренд: Heinner Страницы: 33

Бренд: MBW Страницы: 33

PROFILE P8MSASS6TBB

Бренд: GE Страницы: 60

Бренд: MORLEY PEDALS Страницы: 1

Бренд: RCF Страницы: 2

Бренд: Varimixer Страницы: 55

Бренд: Cloud Страницы: 10

Бренд: Samson Страницы: 2

Бренд: TC Electronic Страницы: 2

Бренд: Philips Страницы: 11

Бренд: Russell Hobbs Страницы: 8

Бренд: Chilton Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды