Solid State Logic AWS 924 Скачать руководство пользователя страница 98

Страница: 98 / 242

Communications Setup Options

Further Talkback, Listen and Red Light communication options are accessed via the TFT screen. The 16 boxes at the base

of the screen indicate the functions assigned to the 16 buttons in two rows of eight below the screen. Press the

SSL

button,

followed by

Misc

Setup

and locate the following options in the list:

Talkback switches are:

Select the operation of the talkback buttons: Momentary / Latching / Auto

(Play) / Auto (Record).

Listen switch is:

Select the operation of the Listen buttons: Latching / Auto (Play) / Auto

(Record).

Red light switch is:

Select the operation of the Red Light switch: Manual / Auto (Play) / Auto

(Record).

TB switches disable Listen:

This allows the Listen function to be switched off when talkback is activated,

thus avoiding feedback problems.

TB to FB:

(Sums / Replaces) When assigning talkback to foldbacks, this option defines

whether talkback sums with or replaces the normal foldback signal.

The ‘Auto’ modes inhibit the Talkback and/or Listen switches when the transport Play or Record tally is lit. Selecting red

light to one of ‘Auto’ modes makes it follow the Play or Record tally.

Oscillator

The ‘oscillator’ is in fact a comprehensive tone and pink noise generator. It is located above the TFT screen, contains

controls for frequency, level and routing of tone or pink noise to the Mix, Record and Track bus outputs and to the monitor

outputs for use in monitor calibration.

OSC ON

activates the oscillator output (surprise, surprise!). It’s good practice to turn the

oscillator off when recording, to prevent any accidental routing to desk outputs.

PINK ON

switches the output from tone to pink noise. Note that the pink noise level can

only be adjusted using the Pink ‘Cal’ preset.

LEVEL

This pot adjusts the level of the tone generator from -25dBu to +20dBu. When

fully anticlockwise, a preset ‘

Cal

’ level is selected which can be calibrated using

the multi-turn presets located below the level control; a red LED lights to show

when the level control is in the calibrated position.

FREQ

This rotary switch provides six preset frequencies.

The oscillator may be routed to the

TRACK

busses, the

MIX

bus and the

REC

bus (individually or simultaneously) using

the switches to the right of the

LEVEL

pot.. The oscillator output is also available on an XLR on the centre section

connector panel.

Analogue Operations

Page 3-26

AWS 924-948 Owner’s Manual

Содержание AWS 924



















































































































































































































































Результаты поиска

Содержание AWS 924

Отзывы:

Бренды по названию

Популярные бренды

Solid State Logic AWS 924, Руководство пользователя

Результаты поиска

Содержание AWS 924

Отзывы:

Бренды по названию

Популярные бренды