Solid State Logic AWS 924 страница 112 Скачать руководство пользователя

Страница: 112 / 242

DAW Control

Communication with your DAW

The AWS connects to your chosen DAW via three MIDI ports at the rear of the console or via MIDI over Ethernet. Each

AWS DAW layer emulates three HUI or MCU controllers. The HUI and Mackie Control (MCU) protocol are widely

supported by DAW manufacturers.

Section 1 details the MIDI and/or network connections between console and computer and the installation of the

ipMIDI driver software and how to configure Protools and Logic. Information relating to other DAW systems is included

later in this section.

Refer to your DAW manual for information on how to configure your software. Once configured and connected,

communication with the DAW will be initialised, and the level of the AWS channel faders, rotary controls and master

functions will be set to match the DAW controls (provided you are in DAW Focus mode and have the right DAW layer

enabled).
When using your DAW without the AWS, you should remove the AWS from the MIDI controllers section of your DAW

(please see the information specific to your DAW).

Logic Handshaking

Logic Audio uses a challenge - response system to automatically detect connected controllers when it boots up. This feature

can be enabled by selecting ‘Logic Handshake’ when choosing the protocol type in

SSL

Misc

Setup

. Selecting any

other MCU protocol will disable this feature.
Additional details will found in section 1

Page 4-4

AWS 924-948 Owner’s Manual

Содержание AWS 924



















































































































































































































































Результаты поиска

Содержание AWS 924

Отзывы:

Похожие инструкции для AWS 924

Бренды по названию

Популярные бренды

Solid State Logic AWS 924, Руководство пользователя

Результаты поиска

Содержание AWS 924

Отзывы:

Похожие инструкции для AWS 924

Бренды по названию

Популярные бренды