Solid State Logic AWS 924 страница 5 Скачать руководство пользователя

Страница: 5 / 242

Introduction

Caution

When installing or servicing any item of SSL equipment with power applied, when cover panels are removed:

HAZARDOUS CONDITIONS CAN EXIST!

These hazards include:

• High energy stored in capacitors
• High currents available from DC power busses
• Hot component surfaces
• High voltages

To reduce the risk of fire, replace internal fuses only with identical type and rating.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is used in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Disposal of WEEE by Users in the European Union

The symbol shown here is on the product or on its packaging, which indicates that this product must not be

disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing

it over to a designated collection point for recycling of waste electrical and electronic equipment. The separate

collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources

and ensure that it is recycled in a manner that protects human health and the environment. For more information

about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste

disposal service or where you purchased the product.

Standards Conformance

This apparatus fully conforms with the current protection requirements of the European community council

directives on EMC and LVD.

AWS 924-948 Owner’s Manual

Page V

Содержание AWS 924



















































































































































































































































Результаты поиска

Содержание AWS 924

Отзывы:

Похожие инструкции для AWS 924

Бренды по названию

Популярные бренды

Solid State Logic AWS 924, Руководство пользователя

Результаты поиска

Содержание AWS 924

Отзывы:

Похожие инструкции для AWS 924

Бренды по названию

Популярные бренды