SOLEOS OXYGEN 3400 Скачать руководство пользователя | Manualshive

Страница: 34 / 45

background image

32

Refer to cable manufactures specification for minimum bending radius.

6.5 Communication and Monitoring Device

There are 2 plugs in the bottom side of the Soleos inverter as the following figure:

These 2 plugs are used for multipoint  communications,  that  is,  up to 50  Soleos inverters can
be  connected  one  by  one  through  these  2  plugs  and  the  cables,  the  upper  computer  can
communicate  with  these  inverters  via  a  single  signal  cable  at  the  same  time,  and  maximum
length  of  the  cable  is  1000m.  Through  these  plugs,  the  user  can  get  the  data  from  these
inverters, and can also configure parameters of them.

«
...
32
33
34
35
36
...
»

Содержание OXYGEN 3400














































Отзывы:

Нет отзывов

Похожие инструкции для OXYGEN 3400

Бренд: Underhill Страницы: 30

Бренд: Wacker Neuson Страницы: 254

Бренд: National Instruments Страницы: 4

Бренд: SunSynk Страницы: 10

exacqVision E Series

Бренд: Exacq Страницы: 70

Indigo ADDEC-210

Бренд: Crystal Vision Страницы: 37

Бренд: Lambda Страницы: 47

Бренд: Rohde & Schwarz Страницы: 653

Бренд: Carbest Страницы: 22

Бренд: MG Страницы: 38

Бренд: Elabs Страницы: 10

Бренд: Synthrotek Страницы: 5

Бренд: Shinybow USA Страницы: 2

Бренд: Kohler Страницы: 12

Бренд: Mastervolt Страницы: 22

Symo Hybrid 3.0-3-S

Бренд: Fronius Страницы: 140

Бренд: SMA Страницы: 272

Бренд: Tascam Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды