Solas BI-46N-SS Скачать руководство пользователя страница 6

Страница: 6 / 57

SÓLAS

CONTEMPORARY FIRE

IMPORTANT SAFETY INFORMATION

Installation and repair should be done by a

qualified service technician. The appliance should

be inspected before use and at least annually by

a professional service technician. More frequent

cleaning may be required due to excessive lint from

carpeting, bedding material, etc. It is imperative that

the control compartments, burners and circulating

air passageways of the appliance be kept clean.

WARNING: Do not operate the appliance with

the glass door assembly removed, or if the glass

is cracked or broken. Replacement of the glass

should be done by a qualified service technician.

WARNING: Use only glass assembly, P/N BI46-

510, which includes the glass panel, frame and

gasket. Do not use substitute materials. Do not

strike or slam the glass front. Do not use abrasive

cleaners. Do not clean when hot.

CAUTION: Do not operate with broken glass.

Keep Furniture

and Other Objects

36" from Fireplace

36" (91.44cm)

Fireplace

Содержание BI-46N-SS


























































Результаты поиска

Содержание BI-46N-SS

Отзывы:

Бренды по названию

Популярные бренды

Solas BI-46N-SS, Руководство по установке и эксплуатации

Результаты поиска

Содержание BI-46N-SS

Отзывы:

Бренды по названию

Популярные бренды