SolarPower SP4002 Скачать руководство пользователя

Страница: 2 / 20

W W W . S O L A R P O W E R . N E T . A U

Page 2 of 20

Revision: 9h Issued: 01 August 2008

This water heater must be installed and serviced by an

authorised person.

PACK CONTENTS

Your SolarPower Solar Water Heater is supplied with the following
components:

SP4002 Series Parts List

Item No.

Qty Description

SP4002 400L storage tank, (with pump attached)

SP225 solar collector

2610mm (L) x 38mm (W) x 25mm (H) x 1.6mm (T) Upper mounting rail
– 3 units required for Cyclone areas

Accessory bag - contains brackets, screws and assorted plumbing fittings for
full panel fit off.

Installation & Owner’s Manual.

Please check to make sure all these components are included with the
kit.

If any of the above listed components are missing or incomplete,
please contact your local distributor.

Содержание SP4002





















Результаты поиска

Содержание SP4002

Отзывы:

Похожие инструкции для SP4002

Бренды по названию

Популярные бренды

SolarPower SP4002, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SP4002

Отзывы:

Похожие инструкции для SP4002

Бренды по названию

Популярные бренды