SolarPower SP4002 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

SolarPower SP4002 Скачать руководство пользователя страница 5

W W W . S O L A R P O W E R . N E T . A U

Page 5 of 20

Revision: 9h Issued: 01 August 2008

Revision: 9h Issued: 01 August 2008

17)

Connect the Solar Hot Pipe and Solar Cold Pipe to the heater and
to the panels.

NOTE: ensure that the water inlet from the system pump flow is to

the lower left edge of the array, and that the water exits the
panels diagonally opposite and through the sensor outlet
fitting, and returns to the solar return on the tank.

18)

Upon completion of the water heater installation, check the panels
and  associated  plumbing  for  leaks  while  the  pump  is  operating.
Leaks above the water line of the tank will suck air in, rather than
leak  water  out.  When  checking  for  leaks,  if  you  can  hear  air
bubbling in the tank after the pump has been running for a while
(more than 5mins), it is likely that air is leaking in somewhere in
the piping.

COLLECTOR INSTALLATION IN CYCLONE AREAS

The

SolarPower SP4002

is

SUITABLE

for installation in cyclonic locations when installed

with an additional rail mounting and brackets to provide the required additional fixing to the roof
frame. This ensures conformance with AS1170.2. Three mounting rails meet the requirement for a C3
rated area.

«
...
3
4
5
6
7
...
»

Содержание SP4002





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды