SolarEdge Smart EV Charger Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 57

SolarEdge Smart EV Charger Скачать руководство пользователя страница 38

Cellular

This wireless communication option (purchased separately) enables using a cellular

network to connect to the monitoring platform.

The Cellular Plug-in is provided with a user manual, which should be reviewed prior to

connection. Refer to

https://www.solaredge.com/sites/default/files/se-cellular-plug-

in-for-inverters-with-setapp-installation-guide.pdf

Communication Connectors

A communication gland with multiple openings is used for connection of the various

communication options. The table below describes the functionality of each gland

opening. Unused openings should remain sealed.

Opening for cable size (diameter)

Connection type

2.5 - 5 mm

RS485

4.5 - 7 mm, with cut

Ethernet (CAT5/6)

2 - 4 mm, with cut

Cable for external wireless or cellular

communication

Figure 9: Communication Gland

The communication board has a standard RJ45 terminal block for Ethernet connection

and a 6-pin terminal block for RS485 connection.

The Cellular Plug-in can be connected to the communication board for optional

wireless connection.

Smart EV Charger Installation MAN-01-00657-1.0

37

Communication Connectors

«
...
36
37
38
39
40
...
»

Содержание Smart EV Charger


























































Отзывы:

Нет отзывов