SolarEdge Smart EV Charger Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 57

SolarEdge Smart EV Charger Скачать руководство пользователя страница 13

Smart EV Charging Safety Instructions

WARNING!

Do not charge a vehicle indoors if it requires ventilation. Contact your EV service
representative for information.

AVERTISSEMENT!

Ne pas recharger un véhicule à l’intérieur si il nécessite une ventilation.
Contactez votre représentant de service pour plus d’informations.

WARNING!

Automatic CCID (charge circuit interrupting device) reset provided.

AVERTISSEMENT!

Réinitialisation CCID (charge circuit interrupting device) automatique incluse.

CAUTION!

Do not use this product if there is any damage to the unit

.

ATTENTION!

Ne pas utiliser pas ce produit si l'appareil est endommagé.

CAUTION!

Do not use an extension cord between the Smart EV Charger Cable and the
Smart EV Charger. You may use a conversion adapter only if it has been
approved by SolarEdge.

ATTENTION!

Ne pas utiliser de rallonge entre le câble du chargeur EV SolarEdge et Smart EV
Charger. Vous ne pouvez utiliser un adaptateur de conversion que s'il a été
approuvé par SolarEdge

Smart EV Charging Safety Instructions

12

Smart EV Charger Installation MAN-01-00657-1.0

«
...
11
12
13
14
15
...
»

Содержание Smart EV Charger


























































Отзывы:

Нет отзывов