SolarEdge 02-700004 Скачать руководство пользователя страница 74

Страница: 74 / 111

Creating an RS485 Bus Connection

The RS485 option enables creating a bus of connected inverters, consisting of up to 31

follower inverters and 1 leader inverter. Using this option, inverters are connected to

each other in a bus (chain), via their RS485 connectors. The first and last inverters in the

chain must be terminated as described on page 75.

RS485 wiring specifications:

Cable type: Min. 3-wire shielded twisted pair (a shielded Ethernet cable (Cat5/5E

STP) may be used)

Wire cross-section area: 0.2- 1 mm²/ 24-18 AWG (a CAT5 cable may be used)

Maximum nodes: 32

Maximum distance between first and last devices: 1 km /3300 ft.

NOTE

If using a cable longer than 10 m/33 ft in areas where there is a

risk of induced voltage surges by lightning, it is recommended

to use external surge protection devices. For details refer to:

https://www.solaredge.com/sites/default/files/lightning_

surge_protection.pdf

If grounded metal conduits are used for routing the communication wires, a

lightning protection device is not required.

If not using surge protection, connect the grounding wire to the first inverter

in the RS485 chain; ensure it is not in contact with other wires. For inverters

with a DC Safety Unit, connect the grounding wire to the grounding bus-bar

in the DC Safety Unit.

NOTE

An additional RS485 port (RS485-Plug-in) is available from
SolarEdge, allowing the creation of RS485 Bus Connection; Refer
to

http://www.solaredge.com/files/pdfs/RS485_expansion_kit_

installation_guide.pdf

The following sections describe how to physically connect the RS485 bus and how to

configure the bus.

To connect the RS485 communication bus:

Chapter 7: Setting Up Communication to the Monitoring Platform

Three Phase System MAN-01-00507-4.2

Содержание 02-700004
















































































































Результаты поиска

Содержание 02-700004

Отзывы:

Бренды по названию

Популярные бренды

SolarEdge 02-700004, Руководство по установке

Результаты поиска

Содержание 02-700004

Отзывы:

Бренды по названию

Популярные бренды