SolarEdge 02-700004 Скачать руководство пользователя страница 47

Страница: 47 / 111

Inverter Configuration – Setup Mode

You can configure the inverter using one of the following:

The internal LCD user buttons

. When using this option, the inverter cover is

removed.

The external LCD light button

. When using this option, removing the inverter cover

is not required. This option of configuration includes a less detailed set of menus.

Configuring the Inverter Using the Internal LCD User Buttons

After inverter installation, an installer may perform basic system configuration.

Configuration is done when the inverter is in Setup mode.

To enter Setup mode:

1. Turn the inverter ON/OFF switch to OFF (AC remains ON).

WARNING!

If the inverter was operating properly (power was produced by the power

optimizers), the following message is displayed.

D C   V O L T A G E   N O T   S A F E
D O   N O T   D I S C O N N E C T
V D C :      7 2 . 0

This message is displayed until the DC voltage is safe (50V). Do not open the

cover until the voltage is safe or until at least five minutes have passed.

2. Press the Enter button for at least 5 seconds. The following message is displayed:

P l e a s e e n t e r
P a s s w o r d
* * * * * * * *

3. Use the three rightmost internal LCD user buttons to type in the following password:

12312312. The following menu is displayed:

C o u n t r y   < I t a l y >
L a n g u a g e   < E n g >
C o m m u n i c a t i o n
P o w e r   C o n t r o l
D i s p l a y
M a i n t e n a n c e
I n f o r m a t i o n

The inverter is now in Setup mode and all its LEDs are lit. The inverter automatically exits

Setup mode if no buttons are pressed for more than 2 minutes.

Three Phase System MAN-01-00507-4.2

Inverter Configuration – Setup Mode

Содержание 02-700004
















































































































Результаты поиска

Содержание 02-700004

Отзывы:

Бренды по названию

Популярные бренды

SolarEdge 02-700004, Руководство по установке

Результаты поиска

Содержание 02-700004

Отзывы:

Бренды по названию

Популярные бренды