SolarEdge 02-700004 Скачать руководство пользователя страница 26

Страница: 26 / 111

Chapter 3: Installing the Inverter

Install the inverter either before or after the modules and power optimizers have been

installed.

CAUTION!

Do not rest the connectors at the bottom of the inverter on the ground, as it
may damage them. To rest the inverter on the ground, lay it on its back, front
or side.

Inverter Package Contents

One inverter with DC Safety Unit (if applicable)

One mounting bracket

Two Allen screws for fastening the inverter to the mounting bracket

DC Safety Unit sealing cover (if applicable, for use in case of inverter replacement)

Installation guide (with activation card and instructions)

Identifying the Inverter

Refer to the sticker on the inverter that specifies its Serial Number and its Electrical

Ratings. Provide the serial number when contacting SolarEdge support. The serial

number is also required when opening a new site in the monitoring platform.

Mounting the Inverter

The inverter is typically mounted vertically, and the instructions in this

section are applicable for vertical installation. Some three phase inverter

models can be installed horizontally (above 10° tilt) as well as vertically,

and at any tilt over 10° up to 90°. For information and instructions for

horizontal mounting refer to

http://www.solaredge.com/sites/default/files/application_note_horizontal_mounting_

of_three_phase_inverters.pdf.

The inverter is supplied with a mounting bracket.

Figure 8: Mounting bracket

Chapter 3: Installing the Inverter

Three Phase System MAN-01-00507-4.2

Содержание 02-700004
















































































































Результаты поиска

Содержание 02-700004

Отзывы:

Бренды по названию

Популярные бренды

SolarEdge 02-700004, Руководство по установке

Результаты поиска

Содержание 02-700004

Отзывы:

Бренды по названию

Популярные бренды