manualshive.com logo in svg

SolarEdge 02-700004, Руководство по установке

Поделиться
Скачать
SolarEdge 02-700004 Скачать руководство пользователя страница 73

 d.  Use a crimping tool to crimp the connector.

 e.  Connect the Ethernet connector to the RJ45 port on the communication board.

 

Figure 24: The RJ45 Ethernet connection

 7.  For the switch/router side, use a pre-crimped cable or use a crimper to prepare an 

RJ45 communication connector: Insert the eight wires into the RJ45 connector in the 

same order as above (

Figure 23). 

 8.  Connect the cable RJ45 connector to the RJ45 port of the Ethernet switch or router. 

You can connect more than one inverter to the same switch/router or to different 

switches/routers, as needed. Each inverter sends its monitored data independently 

to the  monitoring platform.

 9.  The inverter is configured by default to LAN. If  reconfiguration is required:

 a.  Make sure the ON/OFF switch is OFF.

 b.  Turn ON the AC to the inverter by turning ON the circuit breaker on the main 

distribution panel.

 c.  Use the internal user buttons to configure the connection, as described in 

Communication on page 52.

 

NOTE

If your network has a firewall, you may need to configure it to enable 

the connection to the following address: 

Destination Address: prod2.solaredge.com

TCP Port: 22222, 22221, or 80 (for incoming and outgoing data) 

 10.  Verify the connection, as described in .

Verifying the Connection on page 77.

Three Phase System MAN-01-00507-4.2

72

   Creating an Ethernet (LAN) Connection

Содержание 02-700004
















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды