background image

The SolarSpeeder 2 Kit is a very quick Solaroller 
that can cover 3 meters (10 feet) in under 40 
seconds in direct sunlight. Simple to construct and 
a blast to watch, this is a great kit for all beginners!

K SS Solarspeeder                  $27.50 USD/CAD

Herbie the Mousebot is a 9-volt battery-powered 
robot that loves to chase flash light beams. If there 
are several Herbies in the same area, they can be 
configured to chase each other! These little robots 
are so quick, you have to run to keep up to them!

K HM Herbie the Mousebot      $39.95 USD/CAD

Liked the PumLantern? Want more?

There are several more kits Solarbotics offers for any skill level!

201 35th Ave NE

Calgary, AB  T2E 2K5

Canada

N. America Toll Free: 1-866-276-2687

Local / International: 403-232-6268

Fax: 1-403-226-3741

Find  more neat kits, components, articles, resources and more at our official website:

www.solarbotics.com

Like the Mousebot, the K PP Photopopper seeks light 
and avoids obstacles but is solar powered! It’s 
pretty quick, covering a meter per minute (that’s 3.3 
feet!). Newly upgraded with better electronics and 
gold circuit board!

K PP Photopopper                     $45.00USD/CAD

Содержание PumLantern

















Отзывы: