Solar Stik 20-0104016 Скачать руководство пользователя страница 52

Страница: 52 / 79

August 2020

Solar Stik

, Inc.

24VDC PRO-Verter 7000-120 AGS Operator Manual

PRO-Verter/Inverter Reset

To perform an inverter reset:

1. Ensure all AC power (i.e., shore power or generator) is removed from the PRO-Verter.

2. Remove the PRO-Verter Faceplate. The control board on which the RESET button and RESET

LED are mounted is in the center of the PRO-Verter (see below). Locate the RESET button on the
right side of the control board.

3. Press and hold the RESET button for approximately ten (10) seconds until the RESET LED comes

on and flashes rapidly.

4. Once the rapid flashing has begun, release the RESET button. The RESET LED will go off after

the RESET button is released. If the fault does not clear after this procedure, contact the FSR.

Info:

The RESET button is a small

momentary-type switch that
operates by lightly pressing and
releasing. Be careful not to apply
too much force when pushing or
the switch might break.

RESET

LED

RESET

Button

Содержание 20-0104016
















































































Результаты поиска

Содержание 20-0104016

Отзывы:

Похожие инструкции для 20-0104016

Бренды по названию

Популярные бренды

Solar Stik 20-0104016, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 20-0104016

Отзывы:

Похожие инструкции для 20-0104016

Бренды по названию

Популярные бренды