background image

2.

 

Fix  the  heater  assembly  to  the  chains  via  the  hole  in  the  centre  of  the  joining  bar  as 
shown in Fig. E. and ensure the heaters face directly down when hanging.

 

 

3.

 

Secure the supply cable so it is not resting on the body or obstructing the air

-

vents.

 

 

Always isolate the heater from the mains supply when adjusting the position.

 

Unplug/switch off from the mains to the heater or heater assembly power before any 
attempts  are  made  to  replace  the  emitter.  Contact  your  distributor  for  the  correct      
replacement  emitter  quoting  model  type  and  rating  from  rating  label.  It  is  important 
that you read through the emitter replacement procedure before commencing.

 

1. 

Ensure the heater and emitter are cool and the power supply is disconnected or remove 

the plugs from the socket outlet 

-

 all plugs must be removed even if only one emitter is to be 

replaced.

 

 

2. 

Remove the screws from the terminal box at the back of the emitter to be replaced and lift 

off the lid 

-

 see Fig. F.

 

Fig. F

 

Fig. G

 

M A I N T E N A N C E

 

C A U T I O N

 

R E P L A C I N G   A N   E M I T T E R

 

CAUTION: 

Unplug/Switch off unit from the mains supply before replacing emitter or any         

maintenance procedure including cleaning.

 

 

CAUTION: 

Should  dust  or  dirt  appear  on  the  reflector,  it  is  recommended  that  that  the 

guard  and  emitter  are  removed  and  the  reflector  is  wiped  with  a  lint

-

free  cloth  before      

reassembling (see emitter replacement instructions).

 

NOTE: For replacement emitters or spare parts please contact your local distributor 
quoting  model  type  and  rating  from  rating  label.  It  is  very  important  that  your        
replacement emitter is exactly the same as the one it was supplied with. Failure to 
fit the exact same type can cause the heater to prematurely fail.

 

!

 

3. 

Disconnect  the  emitter  from  the  connector  block  by  unscrewing  the  screws  highlighted 

above in Fig. G and remove the white coloured emitter wires from the connector block.

 

CONNECTOR BLOCK

 

9

 

Содержание Alpha H3 SALPHA3-6000















Отзывы: