Solahart POWERPAK 10 kW Скачать руководство пользователя страница 16

POWER

PAK

 Owner’s Manual 

 

 

15 

 

 

Issue Date February 2004 

 

POWER

PAK

 WATER HEATER WARRANTY 

 

(Worldwide) 

 

POWER

PAK

 water heaters are produced by Solahart Industries Pty Ltd (the manufacturer) 

who provide the following manufacturer's warranty. 

 

The protection offered by this warranty is in addition to all other non excludable rights and 

remedies  that  the  consumer  has  under  the  Trade  Practices  Act  (in  Australia)  and  similar 

country, state or territorial laws as they may apply. 

 

The  manufacturer  warrants  the  POWER

PAK

  water  heater  against  manufacturing  defects, 

faulty material and/or workmanship and leakage from corrosion upon the following terms: 

5 years on the tank, internal pipe work and collectors 

 

Note: Collector glass in not included 

3 years on labour 

12 months on all components. 

 

Conditions 

 

1. The above is subject to an area within a 30 kilometre radius of the Solahart dealer from 

whom the unit was purchased. Customers outside this area will be subject to freight and 

travelling charges incurred by the Solahart dealer conducting the work. 

2. Warranty  claims  must  be  submitted  to  the  Solahart  dealer  from  whom  the  water  heater 

was purchased within one month of the component failure. 

3. A call out fee applies to warranty calls made outside normal Solahart business hours. 

 

Exclusions 

 

1. The  manufacturer  shall  carry  no  obligation  under  this  warranty  in  the  case  of  accident, 

Acts  of  God,  installation/repairs  carried  out  by  persons  outside  Solahart  installation  and 

maintenance instructions. 

2. The warranty applies only to the components supplied by the manufacturer and does not 

include plumbing or electrical components supplied by the installation contractor. 

3. No responsibility is accepted for any consequential loss or damage caused by a defect. 

4. No  warranty  applies  to  damage  to  the  heat  exchanger  or  system  caused  by  poor  water 

quality or high mineral content. 

Содержание POWERPAK 10 kW




















Отзывы: