Soil Instruments Digital Inclinometer Pro Скачать руководство пользователя страница 46

Страница: 46 / 51

Bracket does not return to fully extended position:

If the bracket is dirty, clean it. If the problem persists the spring may be

broken or weak.

MOISTURE

MANAGEMENT

Wipe off the instrument cable and probe when you finish the days final

survey. Do not store wet cloth with the probe.

Lubricate the wheels. This helps displace moisture.

WHEEL BRACKET

Probe Inspection

Wheel does not run/spin freely:

Lubricate the wheel bearings with light machine oil.

WHEEL

Probe Maintenance

WHEELS

Lubricate the wheels by applying drops of a light machine oil on the

wheel bearings. Do

not use

WD-40 or any other lubricant spray that

contains chlorinated solvents. Wheels should be lubricated at the end of

each day of usage, prior to storage of the probe.

Cable Inspection

CABLE

Twists:

Twists indicate a poor coiling technique. Change practice - do not pull

the cable over the side of the reel - reel off and reel on.

Work markings:

The user is dragging the cable through the cable gate. Change practice

- pull cable out then up.

Kinks and/or gouges:

If the kinks do not straighten, there is probably internal damage and

liklihood of intermittent reading failures. If there are any deep gouges,

water can enter the cable. In both cases the bad section of cable must

be removed, either by shortening the cable or replacing the cable.

Cable Maintenance

MOISTURE

MANAGEMENT

Wipe off the instrument cable as you draw the probe up on the last run

of the day.

CABLE

When necessary, rinse cable in clean water or wash the cable in a

detergent.

Do not use solvents to clean the cable. Do not submerge the reel.

Содержание Digital Inclinometer Pro




















































Результаты поиска

Содержание Digital Inclinometer Pro

Отзывы:

Похожие инструкции для Digital Inclinometer Pro

Бренды по названию

Популярные бренды

Soil Instruments Digital Inclinometer Pro, Руководство пользователя

Результаты поиска

Содержание Digital Inclinometer Pro

Отзывы:

Похожие инструкции для Digital Inclinometer Pro

Бренды по названию

Популярные бренды