All rights reserved
Shenzhen SOFARSOLAR Co ., Ltd.
C
63
All rights reserved
Shenzhen SOFARSOLAR Co ., Ltd.
C
64
ID66
ID65
UnrecoverHwAcOCP
UnrecoverBusOVP
ID65-ID70 are internal faults of SOFAR inverter, turn
OFF the “DC switch”, wait for 5 minutes, then turn
ON the “DC switch”. Check whether the fault is
rectified. If no, please contact SOFAR technical
support.
The grid current is too
h i g h , a n d h a s c a u s e
unrecoverable hardware
fault
The bus voltage is too
h i g h , a n d h a s c a u s e
unrecoverable fault
ID83
Reserved
ID73
ID72-
Reserved
ID67
UnrecoverIacRmsUnbalance
ID70
ID69
ID68
UnrecoverIpvUnbalance
UnrecoverVbusUnbalance
UnrecoverOCPInstant
ID74-ID77 are internal faults of SOFAR inverter, turn
OFF the “DC switch”, wait for 5 minutes, then turn
ON the “DC switch”. Check whether the fault is
rectified. If no, please contact SOFAR technical
support.
OverTempDerating
ID81
Reserved
ID78- ID80
UnrecoverRelayFail
ID77
UnrecoverREADEEPROM
ID76
UnrecoverWRITEEEPROM
ID75
UnrecoverIPVInstant
ID74
Reserved
ID82
OverFreqDerating
RemoteDerating
RemoteOff
ID84
ID89
ID85-
Reserved
Reserved
Ensure the installation position and installation
method meet the requirements of Section 3.4 of this
user manual.
Check whether the ambient temperature of the
installation position exceeds the upper limit. If yes,
improve ventilation to decrease the temperature.
Check whether the ID90~ID92 fault (fan fault) exist,
if yes, please replace the corresponding fan.
SOFAR inverter automatically reduce the output
power when the frequency of electrical grid is too
high.
SOFAR inverter records ID83 in case of remote power
derating operation. Check the wiring of remote input
and output control signal port on the communication
board according to Section 4.4 of this user manual.
SOFAR inverter records ID84 in case of remote
shutdown operation. Check the wiring of remote input
and output control signal port on the communication
board according to Section 4.4 of this user manual.
T h e g r i d c u r r e n t i s
unbalance,and has cause
unrecoverable fault
T h e i n p u t c u r r e n t i s
unbalance,and has cause
unrecoverable fault
T h e b u s v o l t a g e I s
unbalance,and has cause
unrecoverable fault
The grid current is too
h i g h , a n d h a s c a u s e
unrecoverable fault
Reserved
The input current is too
h i g h , a n d h a s h a p p e n
unrecoverable fault
T h e E E P R O M i s
unrecoverable
T h e E E P R O M i s
unrecoverable
R e l a y h a s h a p p e n
permanent fault
Reserved
the inverter has derated
because of the temperature
is too high
the inverter has derated
b e c a u s e o f t h e g r i d
frequency too hig
The inverter has derated by
the Remote control
The inverter has shut down
because by the Remote
control
Reserved
ID71
UnrecoverPvConfigSetWrong
Check the input mode(parallel mode/ independent
mode) setting of SOFAR inverter according to Section
6 of this user manual.
Incorrect input mode
BusUVP
ID25
BusOVP
ID26
VbusUnbalance
ID27
DciOCP
ID28
ConsistentFault_VGrid
ID49
OverTempFault_Env
ID59
OverTempFault_Boost
ID58
ConsistentFault_FGrid
ID50
ConsistentFault_DCI
ID51
ConsistentFault_GFCI
ID52
SpiCommLose
ID53
PvIsoFault
ID56
OverTempFault_Inv
ID57
SciCommLose
ID54
RelayTestFail
ID55
ID26-ID27 are internal faults of SOFAR inverter, turn
OFF the “DC switch”, wait for 5 minutes, then turn
ON the “DC switch”. Check whether the fault is
rectified. If no, please contact SOFAR technical
support.
Check the input mode(parallel mode/ independent
mode) setting of SOFAR inverter according to
Section 4.5 of this user manual.
If the input mode is correct, turn OFF the “DC
switch”, wait for 5 minutes, then turn ON the “DC
switch”. Check whether the fault is rectified. If no,
please contact SOFAR technical support.
Reserved
ID31- ID48
ID49-ID55 are internal faults of SOFAR inverter, turn
OFF the “DC switch”, wait for 5 minutes, then turn
ON the “DC switch”. Check whether the fault is
rectified. If no, please contact SOFAR technical
support.
Reserved
Reserved
ID64
ID60-
Reserved
If the PV array configuration is correct (no ID5 fault),
the possible cause is that the solar irradiance is too
low. SOFAR inverter automatically returns to normal
operating status after the solar irradiance returns to
normal level.
Check the insulation resistance between the PV array
and earth(ground), if a short circuit occurs, rectify the
fault.
Ensure the installation position and installation
method meet the requirements of Section 3.4 of this
user manual.
Check whether the ambient temperature of the
installation position exceeds the upper limit. If yes,
improve ventilation to decrease the temperature.
Check whether the ID90~ID92 fault (fan fault) exist,
if yes, please replace the corresponding fan.
The bus voltage Is too low
The bus voltage Is too high
The bus voltage is not
balanced
The Dci is too high
Reserved
The grid voltage sampling
value between the master
DSP and slave DSP is not
consistent
T h e g r i d f r e q u e n c y
sampling value between the
master DSP and slave DSP
is not consistent
The DCI sampling value
between the master DSP
and slave DSP is not
consistent
The GFCI sampling value
between the master DSP
and slave DSP is not
consistent
The spi communication
between the master DSP
and slave DSP is fault
The Sci communication
between the control board
communication board is
fault
The relays fault
The insulation resistance is
too low
The inverter temp is too
high
The Boost temp is too high
The environment temp is
too high
Reserved
ID29
ID30
SwOCPInstant
The grid current is too high
Internal faults of SOFAR inverter, turn OFF the “DC
switch”, wait for 5 minutes, then turn ON the “DC
switch”. Check whether the fault is rectified. If no,
please contact SOFAR technical support.
SwBOCPInstant
Ihe input current is too high
Check whether the input current is higher than the
maximum input current of SOFAR inverters, then
check the input wiring, if both are correct, please
contact SOFAR technical support.
SOFAR 10K~20KTL
User manual
SOFAR 10K~20KTL
User manual
