Sofar solar 3K-6KTLM-G2 Скачать руководство пользователя страница 60

Страница: 60 / 79

SOFAR 3K~6KTLM-G2

User manual

- 55 -

ID10

IpvUnbalance

Input current is not

balanced

Check the input mode(parallel mode/

independent mode) setting of inverter according

to Section 6.3 (C) 6.Input Mode of this user

manual, If it’s incorrect, change it according to

Section 6.3 (A) 10.Set Input mode of this

manual.

ID11 PvConfigSetWro

Incorrect input

mode

ID12

GFCIFault

GFCI Fault

If the fault occurs occasionally, the possible

cause is that the external circuits are abnormal

occasionally. inverter automatically returns to

normal operating status after the fault is rectified.

If the fault occurs frequently and lasts a long

time, check whether the insulation resistance

between the PV array and earth(ground) is too

low, then check the insulation conditions of PV

cable.

ID14

HwBoostOCP

The input current is

too high , and has

happen hardware

protection

Check whether the input current is higher

than the maximum input current of inverters,

then check the input wiring, if both are correct,

please contact technical support.

ID15

HwAcOCP

The grid current is

too high , and has

happen hardware

protection

ID15-ID24 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. Ifno, please contact

technical support.

ID16

AcRmsOCP

The grid current is

too high

ID17

HwADFaultIGri

The grid current

sampling error

ID18

HwADFaultDCI The DCI sampling

error

ID19

HwADFaultVGr

The grid voltage

sampling error

ID20 GFCIDeviceFaul

The GFCI sampling

error

ID21

MChip_Fault

The master chip

fault

ID22

HwAuxPowerFa

ult

The auxiliary

voltage error

ID23 BusVoltZeroFaul

The bus voltage

sampling error

ID24 IacRmsUnbalanc

The Output current

is not balanced

ID25

BusUVP

The bus voltage Is

too low

If the PV array configuration is correct (no

ID05 fault), the possible cause is that the solar

irradiance is too low. inverter automatically

returns to normal operating status after the solar

irradiance returns to normal level.

ID26

BusOVP

The bus voltage Is

too high

ID26-ID27 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID27

VbusUnbalan

The bus voltage is

not balanced

Содержание 3K-6KTLM-G2
















































































Результаты поиска

Содержание 3K-6KTLM-G2

Отзывы:

Похожие инструкции для 3K-6KTLM-G2

Бренды по названию

Популярные бренды

Sofar solar 3K-6KTLM-G2, Руководство пользователя

Результаты поиска

Содержание 3K-6KTLM-G2

Отзывы:

Похожие инструкции для 3K-6KTLM-G2

Бренды по названию

Популярные бренды