Sofar solar 3K-6KTLM-G2 Скачать руководство пользователя страница 14

Страница: 14 / 79

SOFAR 3K~6KTLM-G2

User manual

- 9 -

same time, Control Board can trigger the relay so as to protect the internal
components.

Function module

A. Energy management unit

This control can be used to switch the inverter on/off through an external

(remote) control.

B. Feeding reactive power into the grid

The inverter is able to produce reactive power and can therefore feed it into

the grid through the setting of the phase shift factor. Feed-in management can be
controlled directly by the grid company through a dedicated RS485 serial
interface.

C. Limiting the active power fed into the grid

The inverter, if enabled can limit the amount of active power fed into the

grid by the inverter to the desired value (Expressed as a percentage).

D. Self power reduction when grid is over frequency

When the grid frequency is higher than the limited value, inverter will

reduce output power which is necessary for the grid stability.

E. Data transmission

The inverter or a group of inverters may be monitored remotely through an

advanced communication system based on RS-485 serial interface, or remotely
via the WIFI.

F. Software update

SD card is used for updating the firmware

，

You can also contact the

customer service through the collector for remote upgrade.

Содержание 3K-6KTLM-G2
















































































Результаты поиска

Содержание 3K-6KTLM-G2

Отзывы:

Бренды по названию

Популярные бренды

Sofar solar 3K-6KTLM-G2, Руководство пользователя

Результаты поиска

Содержание 3K-6KTLM-G2

Отзывы:

Бренды по названию

Популярные бренды