SNOWJOE Sunjoe GTS4002C-RM Скачать руководство пользователя страница 10

Страница: 10 / 36

Technical Data

Battery Voltage* ..........................24 V D.C.
Battery Capacity .........................2.0 Ah
Charging Time Max ....................1 hr 20 min
Telescoping Pole Length ............3.7 ft to 5.3 ft

....................................................(1.1 m to 1.6 m)
Auxiliary Handle Angles ..............-45° | 0° | 45°
Charger Input..............................100 – 240 V 50-60HZ
Charger Output ...........................25.2V DC 1.4A

Pole Chain Saw
Motor ..........................................350 W
Bar/Chain Length .......................8 inch (20.3 cm)
Cutting Thickness .......................

Max: 7.5 inch (19 cm)

....................................................

Recommended: 6.5 in. (16.5 cm)

Oil Tank Capacity .......................

2.7 fl oz (80 ml)

Overhead Reach Max .................13ft (4 m)
Head Angles ...............................0° to 30°
Battery Run Time Max ................40 mins
Weight (with Battery Installed) ....7.7 lbs (3.5 kg)

Pole Hedge Trimmer
Motor ..........................................250 W
Blade Length ..............................17.7 inch (45 cm)
Cutting Diameter ........................0.6 inch (1.5 cm)
Head Angles ...............................-45° to 90°
Battery Run Time Max ................55 mins
Weight (with Battery Installed) ....7.7 lbs (3.5 kg)

Grass T Edger
Motor ..........................................200 W
Cutting Diameter ........................10 inch (25 cm)
Spool Length ..............................16.5 ft (5 m)
Spool Advance ...........................Auto-feed
Line diameter ..............................0.055 inch (1.4 mm)
Head Angles ...............................0° to 60°
Battery Run Time Max ................50 mins
Weight (with Battery Installed) ....6.2 lbs (2.8 kg)

*Initial no-load voltage, when fully charged, peaks at 24 volts; nominal voltage
under typical load is 21.6 volts.

Unpacking

Carton Contents

• Telescoping pole with auxiliary handle
•

Chain saw head with chain and bar pre-mounted

• Chain saw bar sheath
•

Hex key wrench

•

Hedge trimmer head with blade

•

Hedge trimmer blade sheath

•

Grass t edger head

•

Grass t edger safety guard

•  Pre-wound spool (x2)
•  24V iON+ lithium-ion battery
•  24V iON+ lithium-ion charger
•

Manuals with registration card

• 3.4 fl oz (100 ml) bar + chain lubricant oil

1. Carefully remove the multi-tool system and check to see

that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you find damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe

+ Sun Joe

customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new cordless

multi-tool system. The packaging is made of recyclable

materials. Properly dispose of these materials in

accordance with local regulations.

IMPORTANT!

The equipment and packaging material are

not toys. Do not let children play with plastic bags, foils,

or small parts. These items can be swallowed and pose a

suffocation risk!

Battery Pack Operation

The equipment is powered by a lithium-ion battery. The battery

pack is completely sealed and maintenance free.

Battery Charge Level Indicator

The battery pack is equipped with a push button for checking

the charge level. Simply press the push button to read off the

battery charge level from the LEDs of the battery indicator:

• All 3 level monitoring LEDs are lit: Battery charge level

is high.

• 2 level monitoring LEDs are lit: Battery charge level is

decreasing. Stop work as soon as possible.

• 1 level monitoring LED is lit: Battery is flat. Stop work

IMMEDIATELY and charge the battery. Otherwise the

battery’s service life will be greatly shortened.

B Charger

Содержание Sunjoe GTS4002C-RM





































Результаты поиска

Содержание Sunjoe GTS4002C-RM

Отзывы:

Похожие инструкции для Sunjoe GTS4002C-RM

Бренды по названию

Популярные бренды

SNOWJOE Sunjoe GTS4002C-RM, Руководство оператора

Результаты поиска

Содержание Sunjoe GTS4002C-RM

Отзывы:

Похожие инструкции для Sunjoe GTS4002C-RM

Бренды по названию

Популярные бренды