SNOWJOE Sunjoe GTS4002C-RM Скачать руководство пользователя страница 3

Страница: 3 / 36

19. Maintain the power tool with care – Keep the cutting

edges sharp and clean for optimal performance and to

reduce the risk of injury. Keep the handles dry, clean,

and free from oil and grease. Follow the additional

recommendations described in the maintenance section

of this manual.

20. Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

21. Keep all parts of the body away from the cutting blades/

chain. Do not remove cut material or hold material to be

cut when blades/chain are moving. Make sure the switch

is off when clearing jammed material. The blades/chain will

continue moving for a while after the tool is turned off.

A moment of inattention while operating the power tool

may result in serious personal injury.

22. Carry the power tool by the handle with the cutting blade/

chain stopped. When transporting or storing the power

tool, always keep the blades/chain covered.

Proper handling of the garden tool will reduce

possible personal injury from the cutting blades.

23. Hold the product by insulated gripping surfaces only,

because the cutting blades/chain may contact hidden

wiring. Cutting blades/chain contacting a “live” wire may

make exposed metal parts of the product “live”and could

give the operator an electric shock.

24. The unit has not been designed to provide protection

from electric shock in the event of contact with overhead

electric lines. Never use the power tool near any electrical

power lines. Contact with or use near power lines may

cause serious injury or electric shock resulting in death.

Maintain a minimum clearance of 50 ft (15 m) from all

power lines.

WARNING!

Before inspecting, cleaning, or servicing

the machine, remove the battery and wait for all moving parts

to stop. Failure to follow these instructions can result in serious

personal injury or property damage.

WARNING!

Do not use this appliance without reading

this instruction manual.

WARNING!

Do not use the appliance within range of

persons unless they are wearing protective clothing.

WARNING!

Do not operate the cordless power tool in

a tree, on a ladder, or on a scaffold. Using the tool under such

circumstances is extremely dangerous.

WARNING!

Do not let familiarity with this type of tool

prevent you from taking all necessary precautions. Remember

that a careless fraction of a second is sufficient to inflict

serious injury.

WARNING!

The multi-tool system must be fully

assembled before operation! Do not use the tool that is only

partly assembled or assembled with damaged parts!

WARNING!

Starting, stopping, and restarting an

electric motor repeatedly within a few seconds can generate

a great deal of heat and damage the motor. To protect the life

of your cordless power tool

, always wait at least five seconds

after stopping before restarting the unit.

WARNING!

Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects.

If you find any, do not start up your machine and contact your

distributor.
NOTE: Take care of small parts that are removed during

assembly or when making adjustments. Keep them secure

to avoid loss.
Please contact an authorized Snow Joe

+ Sun Joe

dealer

or call the Snow Joe

+ Sun Joe

customer service center

at 1-866-SNOWJOE (1-866-766-9563) for all maintenance

or operations not foreseen in this manual. Any operation

performed in an unauthorized service center or by unqualified

personnel will completely invalidate the warranty.

WARNING!

For your safety and that of others:

•

Correct maintenance is essential to maintain the original

efficiency and safety of the machine over time.

•

Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

•

Never use the machine with worn or damaged parts.

Damaged parts are to be replaced and never repaired.

WARNING!

Always wear protective gloves during

maintenance operations.

WARNING!

Use only original manufacturer’s

replacement parts, accessories and attachments. Failure to

do so can cause possible injury and poor performance.
To order genuine replacement parts or accessories for the

Sun Joe

GTS4002C-RM cordless lawn + garden multi-tool

system, please visit sunjoe.com or contact the Snow Joe

Sun Joe

customer service center at 1-866-SNOWJOE

(1-866-766-9563).

Cleaning the Tool

WARNING!

Never let any liquid get inside the motor

housing and NEVER

immerse any part of the housing in liquid.

1. Stop the motor and remove the battery.
2. Clean dirt and debris from the body of the tool, using a

damp cloth with a mild detergent.

NOTE: Do not use any strong detergents on the plastic

housing or the handle, as they can be damaged by certain

aromatic oils such as pine and lemon, and by solvents

such as kerosene.

Содержание Sunjoe GTS4002C-RM





































Результаты поиска

Содержание Sunjoe GTS4002C-RM

Отзывы:

Бренды по названию

Популярные бренды

SNOWJOE Sunjoe GTS4002C-RM, Руководство оператора

Результаты поиска

Содержание Sunjoe GTS4002C-RM

Отзывы:

Бренды по названию

Популярные бренды