SNOWJOE Sunjoe GTS4002C-RM Скачать руководство пользователя страница 2

Страница: 2 / 36

, LLC

SAVE THESE INSTRUCTIONS

A Division of Snow Joe

, LLC

OPERATOR’S MANUAL

Model GTS4002C-RM

Form No. SJ-GTS4002C-RM-880E-V1

CORDLESS LAWN + GARDEN

MULTI-TOOL SYSTEM

24-VOLT MAX* | POLE HEDGE TRIMMER | POLE CHAIN SAW | POLE GRASS TRIMMER

IMPORTANT!

Safety Instructions
All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

General Safety

WARNING!

This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.
Before starting up your machine, please check it carefully for

any defects. If you find any, do not start up your machine.

Contact your authorized Snow Joe

+ Sun Joe

dealer or

call the Snow Joe

+ Sun Joe

customer service center at

1-866-SNOWJOE (1-866-766-9563).

WARNING!

When using the power tool, basic safety

precautions should always be followed to reduce the risk of

fire, electric shock, and personal injury. These include:

1. Keep work area clean and well-lit – Cluttered, dark

areas invite accidents.

2. Avoid dangerous environments – Do not use the power

tool in rain, in damp or wet locations, or in bad weather,

especially when there is a risk of lighting. This decreases

the risk of being struck by lighting. Do not operate the

power tool in gaseous or explosive atmospheres or use

the power tool near flammable or combustible liquids.

Motors in these tools normally spark, and the sparks

might ignite fumes.

3. Know your product – Know how to start and stop the

machine. Be thoroughly familiar with the controls.

4. Keep children, bystanders, and pets away –

All spectators, including pets, should be kept a safe

distance away from the work area.

5. Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

CAUTION! – Exercise caution to avoid slipping or

falling. Wear protective footwear that will protect your feet

and improve your footing on slippery surfaces.

7. Stay alert – Watch what you are doing. Use common

sense. Do not operate the power tool when you are tired,

or under the influence of alcohol or drugs.

8. Do not overreach –

Keep proper footing and balance

at all times.

9. Avoid unintentional starting – Do not carry the power

tool with your finger on the trigger. Make sure the switch

is off before inserting the battery.

10. Use the right appliance – Do not use the power tool

for any applications other than those for which it was

intended.

11. Blades are sharp – Don't grasp the exposed cutting

blades or cutting edges when picking up or holding the

power tool.

12. Use two hands – Hold the telescoping pole and handle

with both hands to avoid loss of control.

13. Remove the battery – Remove the battery from the

power tool when it is not in use, before servicing it,

when changing accessories, and when performing any

other maintenance task.

14. Use safety glasses – Also use safety footwear,

snug-fitting clothing, protective gloves, hearing and

head protection.

15. Use head protection – Always use head protection when

operating the power tool overhead. Falling debris can

result in serious personal injury.

16. Do not force the tool – It will perform better with less

likelihood of personal or mechanical injury if it is used at

the rate for which it was designed.

17. Store indoors – When not in use, the power tool should

be stored indoors in a dry and high or locked-up place out

of the reach of children.

18. Check for damaged parts – Before further use of the

appliance, all guards and parts should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other condition that may affect its

operation. A guard or other part that is damaged should

be properly repaired or replaced. Contact the Snow Joe

+ Sun Joe

customer service center at 1-866-SNOWJOE

(1-866-766-9563) for assistance.

Содержание Sunjoe GTS4002C-RM





































Результаты поиска

Содержание Sunjoe GTS4002C-RM

Отзывы:

Похожие инструкции для Sunjoe GTS4002C-RM

Бренды по названию

Популярные бренды

SNOWJOE Sunjoe GTS4002C-RM, Руководство оператора

Результаты поиска

Содержание Sunjoe GTS4002C-RM

Отзывы:

Похожие инструкции для Sunjoe GTS4002C-RM

Бренды по названию

Популярные бренды