SnowEx SP-9300 Скачать руководство пользователя

Страница: 30 / 40

MAX— 30

Center High Mount Stop Lamp (CHMSL)

With spreader mounted on vehicle, plug vehicle (CHMSL) harness into spreader stop lamp harness.

Using supplied harness clamps and screws, route harness along side wall lower corner or so that harness will be out of

the way when spreader is in use.

Locate vehicle ground wire and stop lamp power wire at rear of vehicle. Use supplied wire taps to connect harness to

vehicle electrical system. Once wire taps are installed check to make sure stop lamp works when brake pedal is pressed.
Properly complete installation by tying up any loose wires with ty-wraps. Add electrical tape over both connections

Model # SP-9300

to insure a solid electrical connection. Some newer trucks have auxiliary stop lamp power leads already at the rear for
these types of applications.

CHMSL Spreader Harness

(installed on Spreader from factory)

Key

Part No.

Description

Qty.

D 6158

#10 Lock Nut

D 6514

CHMSL Spreader Harness 1

D 6529

#10 Black Oxide Screw 2

CONNECT TO SPREADER LIGHT

HARNESS 2-CONDUCTOR PLUG

Содержание SP-9300









































Результаты поиска

Содержание SP-9300

Отзывы:

Похожие инструкции для SP-9300

Бренды по названию

Популярные бренды

SnowEx SP-9300, Руководство оператора

Результаты поиска

Содержание SP-9300

Отзывы:

Похожие инструкции для SP-9300

Бренды по названию

Популярные бренды