background image

Version 1 Issue 1

www.snellgroup.com

IQOTR30

Page 4

Technical Profile

Inputs and Outputs 

Signal Inputs (Tx)

Electrical 

3 GBit/s HD-SDI, 1.485 GBit/s HD-SDI or 270 Mbit/s SD-SDI (asynchronous 
operation available at other frequencies)

Connector / Format

BNC / 75 ohm panel jack

Conforms to

SMPTE 424M (HD level A)
SMPTE 292M (HD) 
SMPTE 259M-C (SD)

Inputs

1

Input Cable Length

Up to 80m Belden 1694A @ 3 Gbit/s
Up to 180m Belden 1694A @ 1.5 Gbit/s
Up to 350m Belden 1694A @ 270 Mbit/s

Signal Inputs (Rx)

Optical

3 GBit/s HD-SDI, 1.485 GBit/s HD-SDI or 270 Mbit/s SD-SDI (asynchronous 
operation available at other frequencies)

Connector / Format

SC/PC singlemode panel uniter

Standard

SMPTE 297-2006

Input

1

Signal Outputs 
(Tx)

Optical

3 GBit/s HD-SDI, 1.485 Gbit/s HD-SDI or 270 Mbit/s SD-SDI (asynchronous 
operation available at other frequencies)

Connector / Format

SC/PC singlemode panel uniter

Outputs

1 per channel

Conforms to

SMPTE 297-2006

Electrical

3 GBit/s HD-SDI, 1.485Gbit/s HD-SDI or 270 Mbit/s SD-SDI (asynchronous 
operation available at other frequencies)

Connector Format

BNC/ 75 ohm panel jack
(Reclocked active loop through)

Outputs

2 reclocked active loop through for CH1 SDI Input
1 reclocked active loop through for CH2 SDI Input

Conforms to

SMPTE 424M (HD level A)
SMPTE 292M (HD)
SMPTE 259M-C (SD)

Signal Outputs 
(Rx)

Electrical

3 GBit/s HD-SDI, 1.485 Gbit/s HD-SDI or 270 Mbit/s SD-SDI (asynchronous 
operation available at other frequencies)

Connector / Format

BNC / 75 ohm panel jack

Содержание IQOTR30

























Отзывы: