SMS SenTRI2 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 44

SMS SenTRI2 Скачать руководство пользователя страница 29

29

SenTRI4 fire system

RS232 / RS485 Communication

The control panel offers RS232 and RS485 communication via the IO card.

A standard IO card (not supplied) must be inserted in slot P2 of the backplane of the

panel, which facilitate RS232 and RS485 communication via terminal block P4 on

Terminal card. Note RS232 is PORT 0 and RS485 is PORT 1 with IO card is fitted in

slot P2. The domain address and communication baud rate are configured by setting

the DIL switch located on the left edge of the Display Keyboard card.

PANEL

NETWORK CARD IN SLOT P8

0V1 +VE1 -VE1 0V2 N/C +VE2 -VE2 N/C

IO CARD IN SLOT P8

A 5V B 0V CTS Rx RTS TX

Terminal card

PANEL

Backplane

MCC / LCC

- P1

LOOP or RS232

- P3

I/O or N/W

- P2

LOOP or RS232

- P4

LOOP or RS232

- P5

LOOP or RS232

- P6

LOOP or RS232

- P7

- P8

LOOP, N/W or I/O

IO card

IO or Network

card option

PB1

PB2

IO (RS232) CARD IN SLOT P7

N/C 0V CTS RX RTS TX

IO card option

RS485

A 5V B 0V

RS232

Tx CTS Rx RTS

P4

PORT 1

PORT 0

Terminals for IO card

in slot P2 of the backplane

NOTE: These port settings are

displayed when viewing MCC status.

«
...
27
28
29
30
31
...
»

Содержание SenTRI2













































Отзывы:

Нет отзывов