SMS SenTRI2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 44

SMS SenTRI2 Скачать руководство пользователя страница 21

21

SenTRI4 fire system

Mounting & cable entry points

These instructions cover installation of the panel and battery box. The cards and

batteries are installed during the commissioning of the system by the servicing

organisation.

The control panel can be surface or flush mounted.

Any unused knockouts that have been removed must not be left open.

502mm

390mm

Cable entry points
18 - Back
21 - Top
3 - Bottom side
(on the right)

Mains supply
cable entry
Knock outs

8-off Earth points
(1-0ff bottom side
on the right hand)

5-off Backbox
fixing points
(includes
1 keyhole)

1.7m

Floor level

Dust
cover
over
backplane

Earth to
inner door

Backplane

0V

to printer

PSU

Adhesive backed
foam pad to seal up
gap to prevent ingress

a.  Identify the package SENTRI4 and check that it contains all the parts.
b.  Remove the temporary cover from the Back box if used.
c.  Knock out/in the required cable entry points from the Control panel back box.
d.  Use the fixing points provided to mount the Back box to the wall using suitable

fixings.

«
...
19
20
21
22
23
...
»

Содержание SenTRI2













































Отзывы:

Нет отзывов