background image

20 

 

● 

The LP Gas Cylinder must be a 20 pound cylinder and have a Type 1 Cylinder Valve Outlet 
Connector

 

● 

Handle the Cylinder with care - do not drop it

 

● 

When you are not using the grill, the LP Gas Cylinder should be 
disconnected

 

● 

Connect the regulator and hand tighten firmly

 

● 

Do a leak test each time you connect a LP Gas Cylinder and before 
lighting the grill

 

● 

Never use a match or lit flame to test for leaks

 

● 

To test, prepare a weak solution of detergent and water. Spray or 
swab the 

 

● 

solution onto the connection of the  regulator to the LP Gas Cylinder valve, and

 

● 

on all the joints in the hose connections up to the burner valves (which MUST be 

 

● 

closed in the "OFF" position). Open the LP Gas Cylinder valve, and watch for any

 

● 

bubbles to appear at all the connection points. No bubbles indicate -  All Clear!

 

● 

If there are any bubbles, there is a leak which must be fixed.

 

● 

Never obstruct the flow of combustion and ventilation air.

 

Connecting the LP gas cylinder to the grill 

Lighting the grill 

● 

Always open the Lid before lighting the grill.

 

● 

All burner knobs should be in the "OFF" position.

 

● 

Open the LP Gas Cylinder valve.

 

● 

Note: EACH of the 3 main burners on your grill has its own automatic igniter.

 

● 

Push the knob in fully, and slowly turn it counter-clockwise (to the left) to the "HIGH"

 

position. 

You will hear a loud "Click" as the igniter sparks and lights the burner

 

● 

You can then adjust the knob to your desired setting.

 

● 

If the burner did not light, turn the knob back to the “OFF” position, wait 5 minutes for any gas 
to clear away, and then repeat the lighting procedure.

 

● 

For Sear Burner, turn the knob counter-clockwise (to the left) and then PUSH the Black 
Igniter Button several times to light the burner. If the burner does not light ,then turn the knob 
to the “OFF” position, wait 5 minutes and then try again. 

● 

After using the grill, -  turn all burner knobs to the "HIGH" position and then push fully in and 
turn to the "OFF" position.

 

● 

At once turn the valve on the LP Gas Cylinder OFF.

 

● 

IF the auto-igniter does NOT light the burner, you can light 
it

 

● 

 with a match or a piece of burning paper - hold the match 
or paper with the Match Holder ( attached at the side of the 
grill) , put it through the openings in the Cooking Grid  and 
next to the Flame

 

Tent covering the burner. Then follow the 

lighting procedure above.

 

● 

Observe the proper burner flame -  it should be a blue/yellow color  about 1/2” long.

 

Sear Burner Operation 

 

● 

ALWAYS be sure to OPEN the Lid before lighting the Sear Burner

 

● 

Preheat the Burner for 5 minutes

 

● 

Sear one side of the food, turn the food over and sear the other side. Then continue cooking 
each side of the food on the standard burners until done to your satisfaction

 

● 

When finished, leave the Sear Burner on for a few minutes to burn off grease or food residue

 

OPERATING INSTRUCTIONS 

"click”

 

      

OFF

 

 

      

OFF

 

YELLOW 
 
  BLUE

 

Burner

 

Good Flame

 

Bad Flame

 

Содержание 7000CGS





























Отзывы: