SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 74 / 80

-73-

No. ZK2-OM01301

■

ZK2

□□□ (Vacuum Pump)

The actual suction flow at the point of suction varies depending on the piping conditions to the vacuum port.

■

Precautions

1. The flow rate characteristics show the representative values of the product itself.

They may change depending on piping, circuit and pressure conditions, etc. The flow rate characteristics

and the number of needle rotations vary due to the range of the specifications of the product.

2. The needle has a retaining mechanism, so it will not turn further when it reaches the rotation stop

position.

Turning the needle too far may cause damage.

3. Do not tighten the handle with tools such as nippers.

This can result in breakage due to idle turning.

4. Do not over tighten the lock nut.

It is possible to tighten the standard lock nut (hexagon) manually. When tightening further with tools,

tighten by approximately 15° to 30°. Over tightening may cause breakage.

5. When Vacuum break flow adjusting needle screwdriver operation type needle is selected as

option (K), make sure the lock nut is not loose to prevent the nut from coming off due to vibration.

Port size

Flow rate characteristics of PS to V (Vacuum release side)

Note)

PV port

V port

C[dm

/(s·bar)]

ø6

ø8

0.20

0.06

0.04

Note) When needle is fully open

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды