SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 48 / 80

-47-

No. ZK2-OM01301

○

Mounting the new product to the existing manifold

When the manifold consists of one or 2 stations of the existing valve, or if the 1st or last station need to be

replaced, please replace entire manifold to the new product series.

No change in the position of the hole for mounting the end plate.

For common wiring (D-sub connector, flat

cable), wiring does not need to be changed. Only the end plate needs to be

replaced.

If anything is unclear about the end plate product number, contact your nearest sales office.

Single unit for manifold to be replaced

Existing product

New product

Single unit for new manifold.

D-sub connector

Remove  the  D-sub  connector
from  the  existing  end  plate  and
mount  it  to  the  end  plate  of  the
new product.

New product end plate

Single unit for new manifold.

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды