background image

-68- 

 

No. JXC

-OMY0008 

(5) Refer to a common auto switch (Best Pneumatics No 2), when an auto switch is built and used 

within the system. 

 
 

17.2 Mounting 

Warning 

(1) Install and operate the product only after reading the Operation Manual carefully and 

understanding its contents. 
Keep the manual in a safe place for future reference. 

(2) Tighten threads with the proper tightening torque. 

Tighten the screws to the recommended torque for mounting the product. 

(3) Do not make any alterations to this product. 

Alterations made to this product may lead to a loss of durability and damage to the product, which 
can lead to human injury and damage to other equipment and machinery.

 

(4) When using an external guide, the guide axis should be parallel to the actuator axis. 

There will be damage/excessive wear on the lead screw if the external guide is not parallel. 

(5) When an external guide is used, connect the moving parts of the actuator and the load in such 

a way that there is no interference at any point within the stroke. 

Do not scratch or dent the sliding parts of the actuator tube or piston rod etc., by striking them with 
other objects. Components are manufactured to precise tolerances, so the slightest deformation may 
cause faulty operation. 

(6) Prevent the seizure of rotating parts (pins, etc.) by applying lubricating grease. 
(7) Do not use the product before verifying that the equipment can operate properly. 

After mounting or repair, connect the power supply to the product and perform appropriate functional 
inspections to check it is mounted properly. 

(8) Cantilever 

When the actuator is operated at high speeds while it is fixed at one end and free at the other end 
(flange type, foot type, double clevis type, direct mount type), a bending moment may act on the 
actuator due to vibration generated at the stroke end, which can damage the actuator. In such a case, 
install a support bracket to suppress the vibration of the actuator body or reduce the speed so that 
the actuator does not vibrate. Use a support bracket also when moving the actuator body or when a 
long stroke actuator is mounted horizontally and fixed at one end. 

(9) When mounting the actuator or attaching to the work piece, do not apply strong impact or 

large moment. 

If an external force over the allowable moment is applied, it may cause looseness in the guide unit, 
an increase in sliding resistance or other problems. 

(10) Ensure sufficient space for maintenance activities. 

Allow sufficient space for maintenance and inspection. 

Содержание JXCEH






















































































Отзывы: