background image

 

 

 
 

– 15 –

 

FCC Compliance Statement 

This device complies with part 15 of the FCC rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. 

Note that this equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures: 

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and receiver. 

  Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

  Consult the dealer or an experienced radio/TV technician for help. 

FCC Radiation Exposure Statement:  

  This equipment complies with FCC radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated with 
minimum distance 20cm between the radiator and your body. This transmitter 
must not be co-located or operating in conjunction with any other antenna or 
transmitter. 

Innovation, Science and Economic Development (ISED) 
Canada Compliance Notice 

This  device  complies with Innovation, Science and Economic Development Canada’s 
license-exempt RSS(s). Operation is subject to the following two conditions: 

1.  This device may not cause interference. 
2.  This device must accept any interference, including interference that may cause 

undesired operation of the device. 

Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement 
économique Canada applicables aux appareils radio exempts de licence. L’exploitation 
est autorisée aux deux conditions suivantes: 

1.  L’appareil ne doit pas produire de brouillage; 
2.  L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage 

est susceptible d’en compromettre le fonctionnement. 

Содержание SML-5051W

















Отзывы: