manualshive.com logo in svg

Smartgen HGM8110DC, Руководство пользователя

Поделиться
Скачать
Smartgen HGM8110DC Скачать руководство пользователя страница 17

                                       

HGM8110DC GENSET CONTROLLER USER MANUAL 

HGM8110DC Genset Controller                      2018-12-27                      Version 1.1                Page 17 of 60 

5.6 

GENSET CONTROLLER SWITCH CONTROL PROCEDURES 

5.6.1.  HGM8110DC SWITCH CONTROL PROCEDURES 

5.6.1.1 MANUAL TRANSFER PROCEDURES 

When controller is in manual mode, manual control will be executive. 

Users can control switch on or off by pressing key. 

Press  generator  switch  on  key

,  generator  will  output  load  signals.  Press  generator  switch  off 

key

  , generator will output unload signals.   

5.6.1.2 AUTO CONTROL PROCEDURES 

When controller is in auto mode, switch control procedures will start auto transfer. 

1)    If input port is configured as 

“Close Mains Auxiliary” 

A.   

If “Open breaker detect” is “SELECT Enable” 

Generator load is transferred into generator un-load, after the delay of switch off, detecting transfer 

failure  while  switch  off  output.  When  detecting  time  out,  if  switch  off  failed,  it  will  wait  for  switch  off. 

Otherwise, switch off is completed. 

Generator  unload  is  transferred  into  generator  load,  after  the  delay  of  switch  on,  detecting  transfer 

failure while switch on outputting. When detecting time out, if switch on failed, it will wait for switch on. 

Otherwise, switch on is completed. 

If  transfer failed  and  warning  ―SELECT Enable‖,  there is  alarming  signals  whatever switch on  or  off 

failure. 

B.   

If “Open breaker detect” is “SELECT Disable” 

Generator  load  is  transferred  into  generator  unload,  after  the  delay  of  switch  off,  switch  off  is 

completed. 

Generator unload  is  transferred  into  generator  load, after  the  delay  of  switch on,  detecting  transfer 

failure  while  switch  on  outputting.  When  detecting  time  out,  if  switch  on  failed,  to  wait  for  switch  on. 

Otherwise, switch on is completed. 

If transfer failure warning is ―SELECT Enable‖, there is warning signal that ―switch on fail‖. 

2)    If input port is not configured as Close Mains Auxiliary 

Generator un-load is transferred into generator load, close generator output. 

Generator load is transferred into generator un-load, open generator output. 

NOTE:

 

1) 

When using ATS of no interposition, switch off detecting should “SELECT Disable”; 

2) 

When using ATS of having interposition, switch off “SELECT Disable” or “SELECT Enable” both are OK. If 

choose “SELECT Enable”, switch off output should be configured; 

3) 

When using AC contactor, switch off “SELECT Enable” is recommended. 

 

Содержание HGM8110DC





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды