background image

HGM6510 GENSET PARALLEL UNIT 

HGM6510 Genset Parallel Unit 

ISSUE 2013-07-15 

Version 1.7 

Page 29 of 52 

 

 

7.1.7  EVENT LOG 

EVENTS 

7-1 

First Event Log Screen 

RECORDS: (01/02) 
OVER POWER TRIP 
2010-12-18  21:31:55 

Total Records 
Fault Type 
Record Time 

 

EVENTS 

7-2 

Second Event Log Screen 

RECORDS: (02/02) 
GEN FAIL TO CLOSE 
2010-12-18  08:11:07 

Total Records 
Fault Type 
Record Time 

 

7.1.8 

“ABOUT” DISPLAY 

ABOUT 

8-1 

First About Screen 

MODEL: HGM6510 
SOFTWARE:V4.0.2 
11-03-08 (2) 03:11:32 

Model Type 
Software Version 
Current Time 

 

ABOUT 

8-2 

Second About Screen 

HARDWARE: V1.3 
CPU TEMP:37°C/98°F 
ISSUE DATE: 2011-06-24 

Hardware Version 
Inner Temperature 
Issue Time 

 

7.2  PARAMETER CONFIGURATION 

 

Press and hold 

and then press 

to enter into password screen.  Use 

and 

to increase/decrease values and input the corresponding password    0~9; Use 

or    to  move  the  cursor;  after  you  have  input  the  fourth  digit  press      to  verify  the   

password.  If  the  password  is  correct,  you  will  enter  into  parameter  setting  menu; 

otherwise you will exit directly. (Factory default password is 1234 and it can be changed 

by users). 

Press         and         to scroll screen; select parameter you want to configure and   press 

 

key (the parameter will highlight with   black), press 

key or 

key to change 

parameter  value,  press 

or 

to  move  the  cursor  and  press   

to  confirm 

setting. 

During parameter configuration, pressing  

 

will exit the interface directly and return to 

the main screen. 

Содержание HGM6510



















































Отзывы: