Smart Storm Greasebuster страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 15

background image

7.0 SCRAPPER BLADE ADJUSTMENT

7.1 The scraper blade (7) is mounted to the support bar (15), and the support bar is bolted to the slotted bracket
(16).

7.2 To set the scraper blade release the two screws at the slot of bracket (16) at both sides of the scraper blade
support. Raise the scraper blade to contact the belt, then lock the screws.

7.3 The scraper blade should rest evenly against the belt with minimal contact, if the scraper blade presses too
hard on to the belt then this can cause belt tracking problems.

«
...
7
8
9
10
11
...
»

Содержание Greasebuster
















Отзывы:

Нет отзывов

Похожие инструкции для Greasebuster

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Unex Страницы: 5

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренд: Gait up Страницы: 12

Бренд: Gait up Страницы: 6

Бренд: Gaiam Страницы: 2

Бренд: Jacto Страницы: 12

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: Macht Dental Страницы: 8

Бренд: Launch Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды