manualshive.com logo in svg

SMAC LAC-25, Техническое справочное руководство

Поделиться
Скачать
SMAC LAC-25 Скачать руководство пользователя страница 12

SMAC

                                                               LAC-25 Technical Reference Manual

17

3. Entering Commands

Immediately after power-up, the LAC-25 is ready to accept commands. To verify this, you

can hit the ESC key. If everything is working properly, this should cause a greater than sign (">")
prompt to appear on your display. If not, you need to verify that  the  power  and  communications
connections are correct and verify the compatibility of the communications protocol.

Commands are entered via a  "dumb"  terminal  or host computer  such as a PC compatible.

Commands sent to the LAC-25 should consist of standard ASCII characters, and the command lines
should be followed  by a carriage return. Linefeeds  are not  necessary since they are used for
formatting and  therefore they are ignored. As characters are entered at the keyboard, they should
be echoed on  your display. If your display echoes its own transmitted characters, you will want to
issue the Echo Off (EF) command;  otherwise, the Echo  On  (EN) command (which is the default
mode) should be issued. If you enter an invalid command, the LAC-25  will  respond with a question
mark "?" followed by a code indicating  the type of error and the Status LED will begin to blink.
These codes are listed in Appendix A, LAC-25 Error Code Definitions.

If you make a mistake when entering a command, you can backspace to correct the  error. If

you are  entering  commands and change your mind,  hitting  the ESC key will cancel  the line  and
give a new ">" prompt.

Once a  command  line  has been entered and has finished executing, 

hitting the RETURN

key will cause the same command line to be re-executed.

 While  a set of commands are

executing, hitting the space bar will cause command execution  to pause until the space bar is hit
again.  Also, 

if the  ESC  key  is  hit during execution or pause, command execution will be

terminated,

 and you will receive a new ">" prompt.

Command instructions are intended for use with the following syntax:

[Axis#]Command[Argument]<CR>

or...

[Axis#]Command[Argument],[Axis#]Command[Argument],...etc.

The axis number is normally specified as being  from "1"  to "2"  with "0"  being  used to refer

to both axis' at the same time. Once an axis has been specified, the same one will  remain  in effect
until another is specified. For example, if the following were entered:

1SG100,SD500,SV1000000<CR>

or...

1SG100<CR>
SD500<CR>
SV1000000<CR>

the SG command  specifies the axis number, so the subsequent SD and SV commands  are
performed on the same axis. If the following command were issued:

0TP<CR>

it would have the same affect as issuing these commands:

1TP<CR>
2TP<CR>

Содержание LAC-25









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды