92
8.9
INSTALLATION ONTO THE POLE OF THE ODU WITH SEPARAT-
ED ANTENNA
•
Diameter of the pole
60-114 mm
8.9.1
ODU (Standard Lock)
Mounting kit 1+0 version
•
Supporting plate, fixing bracket with M10 130mm bolts (with washer, spring and nut)
•
1 antenna side flange, variable as function of RF frequency, with relevant screws
•
M10 25mm bolts for ODU mounting
•
ODU with O-ring and devices for ground connection
Mounting kit 1+1 version
•
Supporting plate, fixing bracket with M10 130mm bolts (with washer, spring and nut)
•
M10 25mm bolts for hybrid and ODUs mounting
•
Hybrid mechanical body
•
Polarization twist disk (see
•
2 ODUs with O-rings and devices for ground connection.
8.9.1.1
1+0 ODU with separated antenna
See
•
Position the supporting plate (1) on the pole and fix the rear bracket (2) to it by means of the four
130 mm M10 bolt (3) with relevant washers, springs and nuts (use 15mm spanner, torque =
46Nm).
•
Fix the antenna side flange (4) with the proper screws (in
the antenna flange is shown in two
different positions depending on the polarization), the screw holes side is the side where the wave-
guide must be installed.
•
On the supporting plate, on the opposite side respect to the antenna flange just mounted, insert in
holes (5) on the supporting plate the four 25mm M10 bolts (3): screw them partially, each bolt
should be tightened to have the square head out of the hole of about 13-14 mm (the thickness of
hook (4), use 15mm spanner).
•
Apply seal and lubricant grease Dow Corning 4 to the O-ring, protecting fingers with gloves, and
insert it in the proper track on the ODU flange.
•
Position the ODU vertically near the four bolts on the supporting plate and align the ODU to match
the polarization of the antenna flange:
-
vertical polarization: the handle of the ODU is at the bottom left corner
-
horizontal polarization: the handle of the ODU is at the bottom right corner
•
After the right position has been found, rotate 30° counter clockwise the ODU and approach the
ODU to the supporting plate in order to have the four slots of the Standard Lock cross between the
four bolts
•
Rotate 30° clockwise the ODU to hook each slots on the relevant bolt
Содержание ALFOplus
