Technische Änderungen vorbehalten.
1. NOTES ON SAFETY
Installation, mounting or works on the electrical connection may
only be carried out by an approved electrician.
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no
decoration.
Keep children away from the product.
The fixture may only be operated with a complete and intact
protection glass.
Operate the product only when it functions properly:
In case of a
malfunction
you may
NOT
touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
If touched or further operated there is
danger from electric shock,
burning, or fire.
A
malfunction
exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
2. USE AS DIRECTED
This product serves exclusively lighting purposes and may:
only be used with a voltage of
230V ~50Hz
.
only be operated when firmly mounted.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
3. OPERATION
There may be hot surfaces on the fixture. These surfaces are
indicated on the drawing or on the fixture by the following sign:
Exchange the light source always before it reaches its lifespan, to avoid
personal injuries, or damages of the fixture or other objects.
Disconnect the product from the power supply
, before you exchange
the bulbs. Let the
light source cool down
before replacement.
There exists danger of burning!
Use only light sources that are approved for the product. Approved light
sources are indicated on the type label.
Other types of light sources may cause
fire risk
,
damage the product
or
lead to malfunction
.
Replacing the light source:
Remove the shield and the protection
glass by loosening the screws. Remove the used bulb. Insert the bulb
applying a slight turn to the right. Reattach the shield and the glass.
Check and clean the gasket after each opening of the fixture. The
bearing surface of the gasket must be free of dirt. These measures
ensure that the IP class is maintained.
Note the proper fit for the gasket. Tighten the screws in a cross-wise
order, to achieve an even pressure on the gasket.
4. MAINTANANCE AND CARE
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning
agents
fertilizer especially in flowerbeds
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply
and let it
cool down
,
before you clean the product.
If disregarded there may be
danger of electric shock
or by
burning
when cleaning the product.
Cleaning:
Clean the product on a regular basis using a slightly
moistened, soft and fluff-free cloth. Please also note additional supplied
notes on maintanance and care.
5. ADDITIONAL IMPORTANT NOTES
Storage:
The product must be stored in a dry and clean environment. Do
not strain the product mechanically during storage.
Warranty:
In case of a warranty contact your dealer.
Disposal:
Notes on the correct disposal in Germany are found on
www.slv.de.
6. INSTALLATION
(only by an approved electrician)
Switch off the mains
or respectively the connection lead before doing
any works.
There
exists
mortal danger from an electric shock
.
Use only parts, which are supplied with the product or are described as
accessories
!
Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Inspect the product for
loose parts
inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
The housing maybe voltage-carrying.
Danger of electric shock!
Unpacking
Consignment:
Three protective tubes
Installation pot
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all
components of the product are removed.
Installation place
The product is solely suited for
recessed floor installation
.
Make sure that the product is mounted on a
stable, even and tilt-fixed
background
.
The
light exit
should be placed at least so far from the illuminated
surface, as indicated as
minimum distance
on the type plate of the
luminaire:
.
Pay special caution
to easily inflammable objects
(e.g. foliage).
Before installation
Do not try to seal the product yourself, using additional silicon or another
sealant.
DO
NOT
REMOVE THE GREASE ON THE SCREWS AND THE
SCREW HOLES! The grease inhibits anodic corrosion (electrolysis).
Renew the grease on the screw connections after each time the fixture
has been opened.
Carry out the installation when the weather is dry.
Prepare the recess if not done yet. When installing the lighting unit
outdoors provide a gravel bed, 20 cm thick, beneath the installation pot.
This serves as protection from corrosion.
Prepare the power supply lead according to valid rules for outdoor
installations.
Separate Installation Steps
Remove the shield by loosening the screws.
Take the fixture out of the plastic casing.
Direct the earth cable through the opening of the plastic casing.
Fix the plastic casing firmly into the earth.
Remove the connection plate(a) and the bulb holder(b).
Direct the earth cable, in sufficient length, through the cable screwing.
Secure the cable screwing using a suitable tool.
Electrical Connection
The product must be able to be separated by an all pole separation
from the current supply.
Equip the three wire ends with protective tubes.
For electric connection attach the black or brown wire (live conductor)
of the mains supply with the clamp L and the blue wire (neutral
conductor) of the mains supply with the clamp N. The green-yellow
wire (protective conductor) of the mains supply has to be tightly
screwed into the earth clamp
of the product.
Fix the connection plate and the bulb holder again.
Inserting the bulb:
Insert the bulb applying a slight turn to the right. You
may adjust the position of the bulb now.
Assemble the fixture in reverse order. Pay attention that the gasket fits
properly. The bearing surface of the gasket must be free of dirt. Tighten
the screws on the shield in a cross-wise order, to achieve an even
pressure on the gasket.
The product is now ready for operation.
art.-no. 228430/34
12/2009
© SLV Elektronik GmbH, Daimlerstr. 21-23, 52531 Übach-
Palenberg, Germany, Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
SLV Elektronik GmbH
ENGLISH
INSTRUCTION MANUAL FOR
RECESSED GROUND FITTING
DASAR EXACT GU10
