PARTS LIST
iTEm
parT
DESCripTioN
No.
No.
1a
EBF-120-a
pedestal Faucet Spout and Sensor assembly
(EBF-625)
1B
EBF-81-a
Faucet Spout and Sensor assembly (EBF-655)
2
ETF-1023-a 0.5 gpm (1.9 lpm) Spray head with Key
ETF-1024-a 2.2 gpm (8.3 lpm) aerator Spray head with Key
F-175-l
2.2 gpm (8.3 lpm) laminar Flow Spray head
3
ETF-435
replacement Key oNly for ETF-1023-a and
ETF-1024-a
4a
EBF-123-a
Faucet mounting Kit for EBF-625
4B
ETF-546-a
Faucet mounting Kit for EBF-655
5a
ETF-547
1/8” NpT pipe to 3/8” Tube Compression Fitting
Connection
5B
ETF-617
3/8” Bak-Chek Tee Compression Fitting
5C
EBF-113-a
Single Solenoid Supply Kit
6
EBF-60-a
Control module assembly
7
EBF-79-a
mounting hardware Kit for Control module assembly
8a
ETF-103-a
4” (102 mm) Centerset Trim plate for EBF-625
8B
mix-101-a
4” (102 mm) Centerset Trim plate for EBF-625 with
optional mixing Valve
8C
ETF-105-a
8” (204 mm) Centerset Trim plate for EBF-625
8D
mix-106-a
8” (204 mm) Centerset Trim plate for EBF-625
8E
ETF-576-a
8” (204 mm) Centerset Trim plate for EBF-655
8F
ETF-577-a
8” (204 mm) Centerset Trim plate for EBF-655 with
optional mixing Valve
–
EBF-80-a
Sensor replacement Kit
–
EBF-1011-a Solenoid replacement Kit
–
EBF-1004-a Solenoid Filter replacement Kit (includes Filter Screen
and o-ring)
NoTE: The information contained in this document is subject to change
without notice.
SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131
phone: 1-800-9-ValVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380 • www.sloanvalve.com
Copyright © 2010 SloaN ValVE CompaNy
Code No: 9108237 – rev. 3 (12/10)
1A
2
4A
7
3
5B
6
5A
8A
3
1B
2
4B
5C
5C
8B
8C
8E
8D
8F
if further assistance is required, please contact the
Sloan Valve Company installation Engineerying Department
at 1-888-SloaN-14.
TROUBLESHOOTING GUIDE (CONTINUED)
2. Sensor troubleshooting lED does not function (red indicator light
does not flash during set-up procedure)
No battery power is being supplied to sensor.
Ensure that the batteries are installed properly. Check that the
orientation of each battery matches the positive (+) and negative (-)
symbols shown on the bottom of the battery compartment.
reinsert the battery compartment into the control module.
insufficient battery power is being supplied to sensor.
one (or more) of the batteries is “dead.” To ensure proper
operation, insert four (4) new “C” sized alkaline batteries. Check
that the orientation of each battery matches the positive (+) and
negative (-) symbols shown on the bottom of the battery
compartment. reinsert the battery compartment into the
control module.
Sensor Cable is not properly inserted.
Disconnect and reconnect Sensor Cable to the Control module.
Sensor range is set at minimum distance.
increase Sensor range. use a small screwdriver to turn the
potentiometer screw (white screw in blue base) clockwise.
Control module assembly is defective.
replace EBF-60-a Control module assembly.
3. The water temperature is too hot or too cold on a faucet connected
to hot and cold supply lines with Bak-Chek.
Supply stops are not adjusted properly.
adjust Supply Stops.
NoTE: a thermostatic mixing valve may be required on some systems.
4. Faucet does not deliver any water when Sensor is
activated.
Solenoid valve produces audible “CliCK.” water supply valve is
closed.
open the water supply.
Solenoid valve DoES NoT produce an audible “CliCK”.
Disconnect and reconnect Solenoid lead to the Control module, if
solenoid lead is not properly connected to the Control module.
Batteries are not installed properly. Check that the orientation of
each battery matches the positive (+) and negative (-) symbols
shown on the bottom of the battery compartment. reinsert the
Battery Compartment into the Control module. The troubleshooting
lED should flash rED when a user is detected.
5. Faucet delivers only a slow flow or dribble when Sensor
is activated.
water supply valve is partially closed.
Completely open the Supply Stop.
Solenoid Filter is clogged.
remove, clean, and reinsert. replace EBF-1004-a Solenoid Filter
Kit, if necessary.
aerator or Spray head is clogged.
remove, clean, and reinsert.
