REV. 11-16-18 Page 27
Round Flat Disc Fire Pits
Thermal Safety (Overheat Protection):
Error Code
: 4 Beeps every 2 seconds.
Description of Fault
: Warn users that the modules internal temperature exceeds 170°F.
How to Clear
: Module’s internal temperature must cool to below 160°F and then press ON button.
What to Check
:
1.
Ensure that there is proper ventilation to the control module.
2.
Is module located in unapproved location, too close to burner?
3.
Move to cooler location.
Wireless Remote Transmitter Will Not Operate Appliance
1.
Make sure that the transmitter is within the 25-foot operational range of the control module.
2.
Ensure batteries in transmitter are fully charged and properly installed.
3.
If using the battery pack, ensure batteries are fully charged and properly installed. Also, make sure the battery
pack’s 4-pin connector is securely connected to the battery pack and control module.
4.
If using optional AC adapter, ensure that the AC adapter leads are securely attached to “POWER” connection on
the control module. Also, ensure that the AC adapter is connected to a live 120VAC power source.
5.
Ensure “Remote/Off” switch on control module is set to “Remote”.
6.
Ensure the control module has learned the transmitter’s security code (learning section page 23).
7.
Make sure that the remote transmitter is not placed/mounted to a metal surface, which will reduce the operating
range.
8.
Make sure that there is not a large metal obstruction between the remote transmitter and the control module.
Igniter Electrode Sparks Frequently During Operation
1.
The control module will generate a spark at the igniter electrode if the system is in the ON position, but does not
sense a flame.
2.
Make sure that the flame sensor electrode is clean. Soot buildup will insulate the electrode and will not allow for
proper flame sensing.
3.
Make sure that wind does not blow the flame off of the flame sensor. The sensor hood and the appliance media
(rocks, glass, etc.) provides shielding from the wind. Ensure that the sensor hood and appliance media is properly
positioned per the appliance instructions. If wind is too strong, and the flame will not maintain contact with the
flame sensor, the appliance should not be operated.
Flame Modulation Will Not Work or Works Backwards
1.
Ensure that the black and red leads from the battery pack are securely connected to the red and black leads from
the Hi/Lo latching solenoid located on the valve body (red to red and black to black).
2.
Verify that the selector switch on the battery pack is set to LATCHING SOLENOID only.
3.
Check functionality with all transmitters to determine if there is an issue with the main control system or an
individual transmitter. If the issue is with an individual transmitter, make sure that the batteries in both the transmit
ter and battery pack are installed properly and fully charged.
OUT
PILOT ADJ
IN
MAIN
PILOT
Battery
Pack
Black (Ground)
Orange
Green
White
2-Brown
White
Black (-)
Red (+)
Black (4-Pin Connector)
Red
Red
Black
Black
Lear
n A
UX
Remot
e/OFF
AF-5000MOD-1
Module
I
S
Ignitor
Sensor
Thermocouple Ground Wire
Fig. 29
Wiring Diagram
SECTION C THERMOCOUPLE FLAME SENSE (TFS) INST
ALLA
TION
f i r e - p a r t s . c o m
Содержание Firegear Outdoors FPB-20DBSMT-N
Страница 8: ...REV 11 16 18 Page 8 Round Flat Disc Fire Pits Section A Match Light MT Installation fire parts com...
Страница 30: ...REV 11 16 18 Page 30 Round Flat Disc Fire Pits Replacement Parts Accessories fire parts com...
Страница 37: ...REV 11 16 18 Page 37 Round Flat Disc Fire Pits NOTES fire parts com...
