10
2.1.2 Electric Installa
ti
on
Before to plug the equipment on the socket, make sure the voltage as it is shown on the
cord label, is the same network voltage.
The cord plug has three pin , the middle pin is for grounding. It is mandatory the three
pins to be duly connected, before to start the equipment.
2.2 Pre Opera
ti
on
First make sure the equipment is stable in its posi
ti
on. Before to use the equipment, the
parts that will be in contact with the product that would be processed shall be washed
with water and soap (see item 3.3 Cleaning).
2.2.1 To Disassemble the Plates
Step 1: Remove the Round Stumper # 02 (Pic. 03).
Step 2: Remove the Oblong Stumper # 01 (Pic. 03).
Siep 3: Remove the Lid Fastenings # 06 (Pic. 03) to allow to remove the Chamber Lid # 03
(Pic 03).
IMPORTANT
Before to open the Chamber Lid # 03 (Pic.03) make sure the Plate # 04 (Pic.03)
is stopped.
IMPORTANT
Steel Gloves should be used to handle the Plates, since the knife edges are sharp
and may wound the operator.
Step 4: Remove the Chamber Lid # 03 (Pic. 03).
Step 5: Remove with care the Plate # 04 (Pic.03) turning it counter clockwise and li
ft
ing it.
Step 6: Renove the Expeller Dish # 05 (Pic.03) li
ft
ing it.
2.2.2 To assemble the Plate
Step 1: Place the Expeller Dish # 05 (Pic.03).
Step 2: Place with care the Plate # 04 (Pic.03).
Step 3: Place the Chamber Lid # 03 (Pic. 03).
Step 4: Turn the Lid Fastenings # 06 (Pic. 03) to
fi
x the Chamber Lid in the right posi
ti
on.
15
4.1 Basic Opera
ti
on Procedures
4.1.1 Dangers
Some areas of the electric device have parts that are connected or have parts connected
to high voltage. These parts when touched may cause severe electrical shocks or even be
lethal.
Never touch manual commands such as switches, bu
tt
ons, turning keys and knobs with
your hands wearing wet clothes and/or wet shoes. By not following these instruc
ti
ons
operator could be exposed to severe electrical shocks or even to a lethal situa
ti
on.
4.1.2 Warnings
* The operator has to be well familiar with the posi
ti
on of ON/OFF Switch to make sure the
Switch is easy to be reached when necessary.
* Before any kind of maintenance, physically remove plug from the socket.
* Provide space for a comfortable opera
ti
on thus avoiding accidents.
* Water or oil spilled on the
fl
oor will turn it slippery and dangerous. Make sure the
fl
oor
is clean and dry.
* Before using any commands (switch, bu
tt
ons, lever), be sure it is the correct one. In case
of doubt, consult this manual.
* Never touch any manual commands (switch, bu
tt
ons, lever) unadvisedly.
* If any work is to be made by two or more persons, coordina
ti
on signs will have to be
given for each opera
ti
on step. Every step of the opera
ti
on shall be taken only if a sign has
IMPORTANT
If any recommenda
ti
on is not applicable to your equipment, please ignore it.
4. General Safety Prac
ti
ces
IMPORTANT
Any change in the protec
ti
on systems and safety devices will during opera
ti
on,
create serious risks to the operator physical integrity.
The following safety instruc
ti
ons are addressed to both the operator of the machine as
well as the person in charge of maintenance.
The machine has to be delivered only in perfect condi
ti
ons of use by the Distributor to the
user. The user shall operate the machine only a
ft
er being well acquainted with the safety
procedures described in the present manual. READ THIS MANUAL WITH ATTENTION.
