SECTION 2, Page 9
SJKB-40-D, SJKB-40-D/F
JUN. 1999
NOTE
Platform leveling from platform control console is
not available on European models.
25.
TO ROTATE THE PLATFORM TO THE LEFT:
Press and hold the Turret Rotate Toggle Switch
to the “
ï
“ (left) position. Release the switch
to stop.
26.
TO ROTATE THE PLATFORM TO THE RIGHT:
Press and hold the Turret Rotate Toggle Switch
to the “
ð
“ (right) position. Release the switch
to stop.
27.
TO RETRACT THE BOOM ARM:
Press and hold
the Boom Extend/Retract Toggle Switch to the
“
ñ
“ (retract) position. Release the switch to stop.
28.
TO EXTEND THE BOOM ARM:
Press and hold
the Boom Extend/Retract Toggle Switch to the
“
ò
“ (extend) position. Release the switch to
stop.
29.
TO SOUND THE HORN:
Depress the red push-
button on the Drive/Steer Controller.
30.
TO OPERATE USING THE EMERGENCY
PUMP:
Raise the cover on the Emergency
Pump Select Toggle Switch. Press and hold
the switch to the “
ï
” (left) position. When
the switch is released, power to the emergency
pump will be disconnected. This function is
intended to be used in the event of an engine
failure to lower the work platform for repairs to
be made. This function is not intended to be
used for an extended period of time.
Shutdown Procedure
1.
Fully lower the platform.
2.
Push in the Emergency Stop Buttons.
3.
Rotate the Off/Platform/Base Key Switch to the
” “(off) position. Remove the key.
4.
Rotate the Battery Disconnect Switch to the
“OFF” position.
Loading and Tie Down Procedure
1.
With the telescopic boom fully retracted and
trailer on firm level ground. Align the tires of the
boom with the back end of the trailer.
2.
Select low speed on the platform throttle control
and slightly raise the jib for ground clearance
while loading. Slowly and carefully drive the
machine on to the trailer. In the event of an
engine failure the Emergency Pump can be
used to raise the boom, and steer the work
platform while loading.
NOTE
For loading and unloading using a winch line, see
the drive relief override and brake release
procedures in this section.
REMEMBER
Operating any hydraulic function will reset the
parking brake.
3.
With machine loaded on trailer, tie down as
recommended. (Refer to Figure 2-11.)
Ma40-212
Figure 2-11. Recommended Tie Down Locations
4.
Remove turret lock retaining pin. Lower turret
lock into locked position and reinstall turret lock
retaining pin.
Содержание SJKB-40-D
