Skyjack SJKB-40-D Скачать руководство пользователя страница 19

Страница: 19 / 213

SECTION 2, Page 8

SJKB-40-D, SJKB-40-D/F

JUN. 1999

WARNING

DO NOT

operate any control on the operator’s control

console without your safety devise fastened and properly
securing the safety lanyard to the platform lanyard rings.

Failure to avoid this hazard could result in death or
serious injury!

Attach the safety lanyards of each occupant to
the platform lanyard rings.

Pull out the Emergency Stop Button.

For gas engine machines equipped with the
Dual Fuel Option. Select the desired fuel source.

When the engine is cold, press and hold the
Engine Choke Toggle Switch to the “

“

(right) position while starting engine. Release
switch once the engine starts (Kubota gas
engines) or press and hold Glow Plug Toggle
Switch to the “

“ (right) position for 15 to 20

seconds, then release (Diesel engines).

Turn Engine Stop/Run/Start Select Switch to the
“ ” (start) position until engine starts, then
release.

DO NOT

over crank the starter. (If

engine fails to start after multiple attempts,
consult the TROUBLE SHOOTING section in
the Operational Maintenance and Parts
Manual).

NOTE Engine will not start if foot

switch is depressed

10.

Select desired engine RPM using the Engine
Speed Select Switch.

REMEMBER

The following controls on the Operator’s Control
Console WILL NOT operate unless the Foot Switch
is depressed and held.

NOTE

When the operator is positioned over an axle, the
direction the operator is facing will be FORWARD!

11.

TO DRIVE FORWARD:

Slowly move the Drive/

Steer Controller handle to the “

“ (forward)

position. Release controller handle to stop.

12.

TO DRIVE IN REVERSE:

Slowly move the

Drive/Steer Controller handle to the “

“

(reverse) position. Release controller handle
to stop.

13.

TO STEER:

Depress the rocker on the Drive/

Steer Controller handle in the direction you wish
to steer.

14.

TO ADJUST BOOM FUNCTION SPEED:

Turn

the Boom Speed Control Knob counter-
clockwise to decrease function speed or
clockwise to increase funtion speed. The Boom
Speed Control will affect all lifting, lowering and
rotate functions but will not affect drive or steer
speed.

15.

TO MOVE THE JIB UPWARD:

Press and hold

the Jib Up/Down Toggle Switch to the “

“

(up) position. Release the switch to stop.

16.

TO MOVE THE JIB DOWNWARD:

Press and

hold the Jib Up/Down Toggle Switch to the “

“

(down) position. Release the switch to stop.

17.

TO MOVE THE RISER UPWARD:

Press and

hold the Riser Up/Down Toggle Switch to the
“

“ (up) position. Release the switch to stop.

18.

TO MOVE THE RISER DOWNWARD:

Press

and hold the Riser Up/Down Toggle Switch to
the “

“ (down) position. Release the switch

to stop.

19.

TO MOVE THE BOOM UPWARD:

Press and

hold the Boom Up/Down Toggle Switch to the
“

“ (up) position. Release the switch to stop.

20.

TO MOVE THE BOOM DOWNWARD:

Press

and hold the Boom Up/Down Toggle Switch to
the “

“ (down) position. Release the switch

to stop.

21.

TO ROTATE THE TURRET LEFT:

Press and

hold the Turret Rotate Toggle Switch to the
“

“ (left) position. Release the switch to

stop.

22.

TO ROTATE THE TURRET RIGHT:

Press and

hold the Turret Rotate Toggle Switch to the
“

“ (right) position. Release the switch to

stop.

23.

TO LEVEL THE PLATFORM (Platform is tilted
away from the jib):

Press and hold the Platform

Leveling

Toggle

Switch

the

“

“ (up) position. To stop release the switch.

24.

TO LEVEL THE PLATFORM (Platform is tilted
toward the jib):

Press and hold the Platform

Leveling Toggle Switch to the “

“ (down)

position. To stop release the switch.

Содержание SJKB-40-D






















































































































































































































Результаты поиска

Содержание SJKB-40-D

Отзывы:

Похожие инструкции для SJKB-40-D

Бренды по названию

Популярные бренды

Skyjack SJKB-40-D, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание SJKB-40-D

Отзывы:

Похожие инструкции для SJKB-40-D

Бренды по названию

Популярные бренды