background image

78 

221491AFA 

SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT

Section 6 – Additional Procedures

 

Fold the guardrail

6.7   Fold the guardrail

When folded down, the guardrail system decreases 
the total height of the retracted MEWP for transport.

 WARNING

Fall hazard. To prevent a fall, keep away from the 
sides of the platform when you fold or unfold the 
guardrails. If you do not obey, there is a risk of 
death or serious injury. 

1

Front

Rear

Left

Right

1

 

Guardrail lock-pin 

with lanyard

:

 Use this pin to 

lock the guardrails.

 WARNING

Fall hazard. Fully lower the platform before you 
fold or unfold the guardrails. If you do not obey, 
there is a risk of death or serious injury. 

 WARNING

Before you operate this MEWP, make sure that 
the guardrail system does not have loose or 
missing lock-pins. The guardrail system must be 
in the vertical position. Lock all pins correctly. An 
incorrectly locked guardrail can cause a fall, which 
can result in death or serious injury. 

6.7-1  Fold the guardrail system down

1. 

Make sure the MEWP is on firm, level ground.

2. 

Make sure you fully lower the platform.

3. 

Push the 

emergency-stop

 button on the base 

control console. 

4. 

Turn the 

main power disconnect 

switch to the 

off position.

 WARNING

Fall Hazard. Use the three points of contact 
principle when you use the MEWP ladder to enter 
or exit the platform. If you do not obey, there is a 
risk of death or serious injury. 

5. 

Use the MEWP ladder to enter the platform.

6. 

Close the gate.

7. 

Make sure you fully retract the extension 
platform(s). 

 CAUTION

Install each lock-pin correctly with the detent 
ball of each lock-pin fully through the bracket or 
railing clamp. If you do not obey, there is a risk of 
machine damage

8. 

Remove the 

lock-pins 

from the control console 

mounting bracket 

2

. Put the 

control console 

down on the platform floor.

2

Содержание SJ9233 RT



























































































































Отзывы: