Skyjack SJ9233 RT Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 122

background image

70

221491AFA

SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT

Section 6 – Additional Procedures

Use the platform control console from the ground

6.3-2 Operate the MEWP from the ground

WARNING

Make sure the operator and the control console
point in the same direction as the front of the
MEWP.

Do not drive the MEWP toward yourself.

Keep away from crush hazards. Stay clear of the
MEWP and out of the direction of travel.

When you use a ramp to drive the MEWP on to or
remove it from a transport vehicle, make sure all
personnel, which includes the operator:

▪

Stay away from the direction of a possible tip-
over of the MEWP.

▪

Stay out of the path of movement of the
MEWP down the ramp.

If you do not obey these instructions, there is a
risk of death or serious injury.

CAUTION

Make sure the control console cable does not
become entangled with the MEWP or objects that
surround the MEWP.

If you do not obey, there is a

risk of MEWP damage.

1.

Before you operate the MEWP, do a full worksite
inspection to identify possible hazards in your
work area. Refer to

Section 2.4

.

2.

Cordon-off the pathway you plan to travel.

WARNING

Crush hazard. Make sure that there are no
personnel in the path you will travel. Tell personnel
around the path before you move the MEWP. Use
a second person to monitor the movement of
the MEWP. Make sure that person stays at a safe
distance. If you do not obey, there is a risk of death
or serious injury.

3.

Stay behind or to the side of the MEWP.

4.

Connect the

platform control console cable

to

the

electrical connector

at the rear side of the

MEWP.

5.

Move the

inclined-drive/level-drive

switch to

the inclined-drive position.

6.

Use as low a speed as practical to drive the
MEWP forward to the necessary location.

7.

Push the

emergency-stop

button when the

MEWP is at the necessary location.

8.

Turn the

main power disconnect

switch to the

off position.

WARNING

Fall Hazard. Use the three points of contact
principle when you use the MEWP ladder to enter
or exit the platform. If you do not obey, there is a
risk of death or serious injury.

9.

Use the MEWP ladder to enter the platform.

CAUTION

Make sure each lock-pin is correctly installed with
the detent ball of each lock-pin fully through the
hole.

10.

Install the

platform control console

onto the

mounting bracket. Install the

lock-pin

in the

mounting bracket.

«
...
68
69
70
71
72
...
»

Содержание SJ9233 RT



























































































































Отзывы:

Нет отзывов

Похожие инструкции для SJ9233 RT

Бренд: Bike-Lift Страницы: 35

Бренд: EASTMAN Страницы: 35

Бренд: TIGIEFFE Страницы: 124

Бренд: JLG Страницы: 98

Бренд: JLG Страницы: 195

Бренд: JLG Страницы: 234

Бренд: JLG Страницы: 262

Бренд: Genie Страницы: 38

Бренд: Genie Страницы: 65

ZX-135/70 with Jib-Extend

Бренд: Genie Страницы: 82

Бренд: Genie Страницы: 185

Бренд: Genie Страницы: 205

Бренд: Beck Страницы: 36

Бренд: Oshkosh Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды