Skyblade Turboprop 10' Скачать руководство пользователя страница 35

Страница: 35 / 40

SKYbLADe FANS

Where Form Follows Function

Check the power wiring page

provided in the IOM.

Is the wiring correct?

TroubLeShooTiNg

Fix the wiring issue.

Does the LED light blink once

every three seconds?

See Fault Code chart

below for next steps.

Consult factory.

FAULT CODES

Voltage

5 Blinks/Second

The Drive is undergoing some voltage issue. Make sure that the correct

voltage is going to the fan.

• If the voltage is high at splice of the fan motor. Over-volt may be

occurring a line reactor may need to be placed to reach correct

voltage.

• If the voltage is low at splice of the fan motor. Under-volt may be

occurring a line reactor may need to be placed to reach correct

voltage.

Vibration

8 Blinks/Second

Check all brackets and bolts. Ensure bolts are torqued to the proper

rating.

Overtemp

7 Blinks/Second

If multiple fan diameters are being used make sure the correct blades

are on the motor. Verify that no external disturbances are occurring with

the blades.

No LED Light

• If incorrect voltage is wired to the fan it may cause the drive to Blown.

Driver will need to be replaced . Contact Factory.

• If the wrong fuse is placed on the breaker and a spike occurs the drive

may have been blown. Driver will need to be replaced . Contact

Factory

Consult factory.

Yes

NOTE

: Fan blades must be ON in order to troubleshoot.

Содержание Turboprop 10'









































Результаты поиска

Содержание Turboprop 10'

Отзывы:

Похожие инструкции для Turboprop 10'

Бренды по названию

Популярные бренды

Skyblade Turboprop 10', Руководство по установке

Результаты поиска

Содержание Turboprop 10'

Отзывы:

Похожие инструкции для Turboprop 10'

Бренды по названию

Популярные бренды